Download  Print this page

KitchenAid KCC-151 Installation Instructions page 2

Hide thumbs
   

Advertisement

INSTALLATION
INSTRUCTIONS
BEFORE YOU BEGIN,
READ THE FOLLOWING
INSTRUCTIONS
COMPLETELY
AND
CAREFULLY.
THEY WILL SIMPLIFY
THE INSTALLATION.
1.
After
removing
the shipping
carton,
be sure to remove
all protective
packaging
materials
such
as tape
and
shipping
pads.
Put
extra
key-knob
In a safe
place
Waxy
residue
from
protective
shipping
material
may
be removed
from
compactor
with
a mild
solution
of
liquid
household
cleaner
and water.
2.
Your
compactor
is designed
for recessed
installation.
A six (6) inch
clearance
from
the right
edge
of the
drawer
front
is desirable
for added convenience
in bag
removal.
Also
allow
twenty-three
(23) Inches
in front
of the appliance
for drawer
removal.
See Figure
3.
COMPACTOR
\\I
WALL OR
OTHER
OBJECTS
l&l
=a
u
2-J"
,,
\\
6
FIGURE 3
3.
The compactor's
overall
dlmenslons
are
Height
34.
l/16"
(min.),
Depth
24".
Width
15". Select
a cabinet
opening
to fit. See Fi.qure
4.
MIN
FIGURE 4
4.
Remove
drawer
as shown
a
Grip
handle
and
raise
front
of drawer
uri!!!
,I
clears
stops
See Figure
5
b.
Grasp
side
ridges
of !he drawer
and lift drawr>r
out
See Flgure
6.
\
FIGURE 5
FIGURE 6
5.
Remove
any materials
that are shipped
In the drawer
Some
models
have
a literature
storage
compartment
located
inside
the front
panel.
See Figure
9. DO NOT
REMOVE
THE BAG.
6.
Lay
two
carton
corner
posts
or
other
protective
material
(such
as a throw
rug) on the floor,
then
lay
the umt on either
of Its sides on the corner
posts.
The
corner
posts
will
protect
the finish
of the compactor
and
the
floor
See Figure
8. NOTE:
Do not truck
or
handle
by console.
FIGURE 8
Remove
the cardboard
shipplng
pad located
on the
bottom
See Figure
8
Stand
compactor
upright
7.
A grounded
receptacle
should
be located
18" (mln )
from
the floor
and in the center
of the opening.
See
Fioure
9
8.
FIGURE 9
Before
moving
the compactor
Into posItion,
measure
the
cabinet
opening
as
shown
In Figure
70
To
determIne
If height
adjustmenr
IS
required.
see steps
9 and
10 below
-CABINET
OPENING
FIGURE 10
9.
The rear
wheels
of your
compactor
are preset
for a
mlnlmgm
cabinet
opening
of 34-l
'8"
to 34-l
14"
(posItIon
A)
To adjust
for
higher
openings.
t:ll
the
compactor
to one side and support
with
a corner
post
or a screwdrtver
handle
CAUTION:
Use
care
so that
the compactor
does
not
drop
on your
hand.
10.
To adjust
the height.
remove
screw
from
posltton
A"
In Figure
11.
Move
the
rear
wheel
and
screw
to
posltlon
"B or C",
34-l/4"
to 34.1,*2"
use position
"B"
34-l/2"
to 34.3/4"
use posltion
"C"
A
w
",:
FIGURE 11
Repeat
for other
rear
wheel
2

Advertisement

Table of Contents
loading