Related Manuals for Jacuzzi Verona
Summary of Contents for Jacuzzi Verona
- Page 1 ™ J-CORNER SHOWER TOWER ™ ENCLOSURE-Verona INSTALLATION AND OPERATING MANUAL BATH WHIRLPOOL...
-
Page 3: Table Of Contents
Important The bath must be installed according to installation instructions (F258000) for the Verona™ whirlpool bath. Follow the instructions to ensure that proper framing has been provided to support the J-Corner Shower Tower. Finishing materials must be waterproof and sealed so that spray and condensation do not cause moisture dam- age. -
Page 6: Shower Tower Hardware Identification Chart
Shower Tower Hardware Identification Chart The diagrams for these fasteners are shown actual size for fast identification. HARDWARE SLOT FASTENER BOLT HEX LOCKNUT #8-32 10X32 QTY.-8 QTY.-1 FLAT WASHER #10 TYPE A HEX NUT WASHER STAINLESS STEEL QTY.-8 10X32 QTY.-3 SCREW SHEET METAL SET SCREW... - Page 7 Shower Tower Hardware Identification Chart The diagrams for these fasteners are shown actual size for fast identification. HARDWARE PLUMBING HARDWARE WATER INLET HARDWARE FIBER WASHER K WASHER .75 O.D. FIBRE WASHER QTY.-1 WASHER 1.24 DIA QTY.-1 STANDOFF QTY.-3 EXTERNAL TOOTH LOCK-WASHER M4 M WASHER STAINLESS STEEL...
-
Page 8: Tower Assembly
TOWER ASSEMBLY 1. Assemble the four (4) bails to the tower wall. (See Illustration 1.) Do not overtighten the nuts on the threaded shaft end. Overtighten- ing may break the stud. BAIL WASHER (8) D BOLT SLOT BOLT (8) NUT (8) FASTENER QTY.-8 10 X32... - Page 9 3. Attach the wallbar assembly to the tower wall. WALL BAR (See Illustration 3.) 1/8" BEAD OF CAULK WALLBAR STAND-OFF EXTERNAL TOOTH WASHER F (2) SHOWER WALL SCREW E (2) H (2) FLAT WASHER SIDE VIEW G (2) OF WALLBAR WALLBAR SHOWER HEAD BRACKET...
-
Page 10: Water Lines To Mixer/Diverter Valve
WATER LINES TO MIXER VALVE M/F 90 ELBOW K WASHER QTY.-1 WASHER FIBER WASHER M/F 90 .75 O.D. ELBOW WATER SUPPLY MIXER VALVE TO SHOWER (12") HOT WATER LINE (48") SCREW (6) STANDOFF (3) L M/F 90 ELBOW PLUG COLD WATER LINE (48") L STANDOFF SCREW... - Page 11 6. Attach the shower line to the water inlet (12" hose). (See Illustration 6.) TOWER WALL 90 ELBOW FIBER WASHER K WASHER .75 O.D. QTY.-1 WATER INLET FIBER WASHER 12" HOSE ILLUSTRATION 7. Attach the three (3) pins to the bottom of the tower. (See Illustrations 7 and 8.) TOWER PINS LOCATED IN HARDWARE PACK...
-
Page 12: Tower Installation
TOWER INSTALLATION BATH FLANGE EDGE BATH FLANGE EDGE TOWER WALL 9/32" HOLE (3) TAPE FIRMLY (TYP) 3/16" HOLE (5) INNER ORANGE CIRCLE TEMPLATE ILLUSTRATION 9 (LEFT HAND SHOWN) CEMENT BOARD TILE OR FINISH MATERIAL STUD WALL MORTAR FLANGE CAULKING MORTAR & FINISH MATERIAL THICKNESS BATH RIM ILLUSTRATION 9A... -
Page 13: Tower Disassembly
DISASSEMBLY INSTRUCTIONS Although the J-Shower Tower is shipped partially assembled, it will have to be partially disassembled to install. After removing packing materials, follow the instructions below. 1. Remove end cap on the lower track. (Page 18, illustration 24.) 2. Remove the top ring. (Page 15, illustration 19.) 3. -
Page 14: Placing Tower
PLACING TOWER CAULK SET BACK 13/32" SCREW M4.2X19MM STAINLESS STEEL QTY.-3 ILLUSTRATION 11 7. Dry fit tower pins into holes to check hole location. Apply sealant around the three tower wall holes on the bath and around the perimeter where the tower will sit. (See Illustration 11.) 8. -
Page 15: Fixed Panel Assembly
FIXED PANEL TO BOTTOM RAIL M4.2X19MM SCREW STAINLESS STEEL QTY.-2 DRILLING FIXED PANEL FIXED PANEL SCREWS IMPORTANT: MUST DRILL AT A 15 ANGLE TO AVOID 1/8" DRILLING THROUGH SIDE OF RAIL. LAY A 1/4" BEAD OF SEALANT UNDER THE BOTTOM RAIL FIXED PANEL ILLUSTRATION 12 ILLUSTRATION 13... - Page 16 FIXED PANEL ASSEMBLE TO BATH CAULK VERTICAL EDGE OF TOWER FASTENING SEQUENCE GENTLY PUSH THIS AREA (4) R ILLUSTRATION 15 LOCATED IN HARDWARE KIT M4.2X19MM HEX LOCKNUT SCREW STAINLESS STEEL QTY.-1 #8-32 QTY.-4 FLAT WASHER SET SCREW WASHER SCREW #8 TYPE B #8-32 x 1 1/2"...
-
Page 17: Mounting Top Ring And Wall Bracket To Tower
RING TOP PLANE MARK 12. Locate the top ring. Remove the plastic retainer extrusion and set it aside for later use. Place the top ring on the fixed panel and tower wall. The top ring groove on the underside of the top ring STUD WALL must mate with the top of the fixed panel. - Page 18 DRILLING TOP RING 14. Drill a 3/32" diameter hole into the top ring at a 15 angle. (See Illustration 20.) Engage the top of the fixed panel with the top ring groove. Secure the top of the fixed panel to the top ring. (See Illustration 21.) IMPORTANT: MUST DRILL AT A 15 ANGLE TO AVOID...
-
Page 19: Fixed Glass Frame End Attachment
FIXED GLASS FRAME END ATTACHMENT EXTRUSION SEALANT FIXED GLASS ILLUSTRATION 23 16. Apply sealant in frame and extrusion. Align and place extrusion above end cap onto the fixed glass. -
Page 20: Sealing And Trimming
L-EXTRUSION L-EXTRUSION WALL BACK SCREW WALL SEALANT WALL BACK WALL SEALANT SCREW END CAP ILLUSTRATION 24 LOCATED IN HARDWARE PACK M3.5X9.5MM SCREW STAINLESS STEEL QTY.-1 QTY. -1 17. Install on the sides of the tower the aluminum extrusions provided. They may be sealed in place or secured with screws (S, quantity 6). -
Page 21: Attaching Face Plate
ATTACHING FACE PLATE HANDLE INSTALLATION FOAM GASKET FACEPLATE TOWER WALL SCREW FOAM GASKET WASHER ILLUSTRATION 26 PLUG SEALANT 18. Assemble the face plate and handles as shown in Illustrations 25 and 26. Attach the shower hose to NAME PLATE LOGO QTY.-1 the hand held shower. - Page 24 Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of this product. Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.