AEG 570 D Operating And Installation Manual
Hide thumbs
Also See for 570 D:
- Operating and installation instructions (20 pages) ,
- Operating and installation manual (20 pages) ,
- User manual (128 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AEG 570 D
Summary of Contents for AEG 570 D
-
Page 2: Table Of Contents
Changing the light bulb What to do if Special accessories Technical assistance service Technical Specifications Electrical connection Installation Removing the hood from cabinet Relocating the control unit (Only 570 D - 5708 D) Printed on recycled paper AEG - putting words into action... -
Page 3: Safety Warnings
Safety warnings For the user • The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. • Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. - Page 4 approximately the same as the outlet hole. • National and regional building regulations impose a number of restrictions on using hoods and fuel-burning appliances connected to a chimney, such as coal or oil room-heaters and gas fires, in the same room. •...
-
Page 5: Description Of The Appliance
• The hood is supplied as an extractor unit and can also be used with a filtering function by fitting one charcoal filter. • You will need an original AEG charcoal filter for this function (Available from your local AEG Service Force Centre). -
Page 6: Control Panel
= Sliding speed control Motor switch 0 = Motor OFF 1 = Speed 1 - Slow 2 = Speed 2 - Booster 1 Medium (Only 570 D) 3 = Speed 3 - Fast Booster 1+2 (Only 5708 D) Fig. 3... -
Page 7: Maintenance And Care
DL 4150 - CHDL 4150 - DL 6250 • Press the handle that locks the grease filter first towards the opposite side and then extract downwards. Fig. 4. 570 D - 5708 D • Fold the handles downwards and press them towards the centre. Fig. 4. - Page 8 Hand washing Soak grease filters for about one hour in hot water with a little washing up liquid added, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry. Dishwasher Place grease filters in the dishwasher.
-
Page 9: Charcoal Filter
• The charcoal filter should only be used if you want to use the hood in the recirculation function. • To do this you will need an original AEG charcoal filter (available from your local Service Force Centre). • The charcoal filter cannot be washed nor regenerated. -
Page 10: Changing The Light Bulb
Warning • Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. • The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. -
Page 11: What To Do If
What to do if If your appliance fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start... Check that: The hood is connected to the electricity supply. Check that a fan speed has been selected The cooker hood is not working Check that:... -
Page 12: Special Accessories
Service and spare parts for UK In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your call will be automatically routed to the Service Centre covering your post code area. -
Page 13: Technical Specifications
230 V 230 V 230 V 230 V 570 D 5708 D 515 mm 715 mm 510 mm 710 mm 548 mm 748 mm Fig. 7 570 D - 5708 D Fig. 7 DL4150 - DL 6250 - CHDL 4150... -
Page 14: Electrical Connection
Electrical connection (not for UK) Safety warnings for the electrician Before connecting the appliance to the power supply, check that the voltage indicated on the rating plate corresponds to the mains power supply available. Appliances fitted with a plug can be connected to any standard power socket within easy access. -
Page 15: Installation
Installation - Fig. 8 • Drill the base of the wall unit to allow for passage of the hood body. Fig. 7. • Drill the top of the wall unit to allow for passage of the exhaust pipe and the electrical cable. Fig. 7. •... - Page 16 Fig. 8...
-
Page 17: Removing The Hood From Cabinet
Removing the hood from cabinet Follow these steps: • Remove the grease filter. • Remove the 4 additional screws from the frame. • Loosen the screws on the two fixing springs. Fig. 9. Fig. 9 • Push a flat screwdriver into the hole for the fixing springs (right and left) and push each of the fixing springs inwards. -
Page 18: Relocating The Control Unit (Only 570 D - 5708 D)
Relocating the control unit (Only 570 D - 5708 D) The control unit can be fitted at a different point (cladding, lighting facia, etc.). Remove the grease filter grill and the housing frame. 1. Loosen two screws and pull the control unit forwards out of the housing. - Page 19 From the Electrolux Group.