Audiolab 8000AP User Instructions page 2

Statutory & Safety Information
CAUTION!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER
NO USER-REMOVEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
ADVERTISSEMENT: RISQUE DE CHOC ELECTRIQUE-
NE PAS OUVRIR
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
IMPORTANT SAFETY INFORMATION
Read these instructions.
Keep these instructions. In the event that you pass the product to a
third party this instruction manual should be provided along with
the product.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
Do not defeat the safety purpose of the polarized or grounding
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wider blade or the third prong are
provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete
outlet.
Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Use only attachments/accessories specified by the manufacturer.
Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
Unplug this apparatus during lightning storms or when unused
for long periods of time.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally,
or has been dropped.
Warning: To reduce the risk of fire or electrical shock, do not
expose this product to rain or moisture. The product must not be
exposed to dripping and splashing and no object filled with
liquids such as a vase of flowers should be placed on the product.
No naked flame sources - such as candles - should be placed on
the product.
Caution: Changes or modifications not expressly approved by
the manufacturer could void the user's authority to operate this
device.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television
reception, which can be determined by tuning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Re-orientate or re-locate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
Mains supply and safety
Class II construction double insulated. These products
must not be connected to earth.
Power Cord: An AC power cord is normally supplied with a
mains plug suitable for your area. If you have any doubts, consult
your dealer about obtaining a suitable power cord.
Mains Supply: The mains voltage of Audiolab units is shown on
the rear panel. If this does not match the voltage in your area,
consult your dealer. The mains supply fuse is on the rear panel. If
it has broken, check for any obvious cause before replacing the
fuse with one of the correct rating and type. The fuses for all areas
are type T (time lag ) AL 20mm.
The fuse values are: 220-240V:T1.0A 100-120V: 1.6A
Fuse Carrier
The fuse is located in a slide-in
carrier which also contains a spare
fuse. The carrier can only be pulled
out after the IEC power cord is
unplugged. When the carrier is
opened the first fuse is the spare.
Remove and safely dispose of the
blown fuse before replacing it.
IEC Mains Connector
Important notice to UK users
The appliance cord is terminated with a UK approved mains plug
fitted with a A fuse. If 3 the fuse needs to be replaced, an ASTA or
BSI approved BS1362 fuse rated at 3A must be used. If you need
to change the mains plug, remove the fuse and dispose of this
plug safely immediately after cutting it from the cord.
Connecting a Mains Plug
The wires in the mains lead are coloured in accordance with the
code: Blue: NEUTRAL Brown: LIVE
As these colours may not correspond to the coloured markings
identifying the terminals in your plug, proceed as follows:
The Blue wire must be
connected to the terminal
marked with the letter N or
coloured BLUE or BLACK.
The BROWN wire must be
connected to the terminal
Blue
marked with the letter L or
(Neutral)
coloured BROWN or RED.
3A FUSE
BS 1362
BROWN
(Live)