Download  Print this page

Electrolux EHG 679 B Instruction Booklet

Hide thumbs

Advertisement

Quick Links

G a s H o b
INSTRUCTION BOOKLET
Models EHG 679 B - EHG 679 W
GB
35670-3001
2

Advertisement

loading

  Also See for Electrolux EHG 679 B

  Related Manuals for Electrolux EHG 679 B

  Summary of Contents for Electrolux EHG 679 B

  • Page 1 G a s H o b INSTRUCTION BOOKLET Models EHG 679 B - EHG 679 W 35670-3001...
  • Page 2: Important Safety Information

    Important Safety Information You MUST read these warnings carefully before installing or using the appliance. If you need assistance, contact our Customer Care Department on 01635 522799 Installation This appliance must be installed by qualified Ensure the control knobs are in the ‘OFF’ position personnel, according to the manufacturer ’s when not in use.
  • Page 3: Table Of Contents

    Contents For the Installer For the User Technical Data Page 12 Description of the Appliance Page 5 Important Safety Requirements Page 13 Operation Page 6 Installation Page 14 Maintenance and Cleaning Page 7 Gas Connection Page 14 Something Not Building In Page 15 Working? Page 8...
  • Page 4: Description Of The Appliance

    Description of the Appliance 1. Hob Top 2. Rapid Burner 3. Semi-rapid Burners 4. Auxiliary Burner 5. Control knob for back right burner (semi-rapid) 6. Control knob for back left burner (semi-rapid) 7. Control knob for front left burner (rapid) 8.
  • Page 5: Operation

    Operation HOB BURNERS To light a burner, turn the relevant control knob anticlockwise to maximum position and push it down to ignite. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated...
  • Page 6: Maintenance And Cleaning

    Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the appliance from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
  • Page 7: Something Not Working

    Something Not Working? If the appliance is not working correctly, please carry out the following checks before contacting your local Electrolux Service Force Centre. SYMPTOM SOLUTION There is no spark when lighting the gas Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown...
  • Page 8: Electrolux Service Force

    ELECTROLUX SERVICE FORCE To contact your local Electrolux Service Force Centre telephone 0990 929929 NORTH EAST ISLE OF LEWIS ND Macleod CHANNEL ISLANDS (M69) 16 James Street Stornoway GUERNSEY Guernsey Electricity GATESHEAD Unit 356a Isle of Lewis PO Box 4 (M39) Dukesway Court PA872QW...
  • Page 9 ELECTROLUX SERVICE FORCE To contact your local Electrolux Service Force Centre telephone 0990 929929 MIDLANDS LONDON & EAST ANGLIA SOUTH EAST BIRMINGHAM 66 Birch Road East, CANVEY ISLAND 2-4 Sandhurst ASHFORD Unit 2 (M18) Wyrley Road Industrial Kings Road (M58) Bridge Road Business Estate Canvey Island...
  • Page 10: Guarantee Conditions

    Guarantee Conditions * Appliances found to be in use within a ELECTROLUX STANDARD GUARANTEE commercial or similar environment, plus those CONDITIONS which are the subject to rental agreements. We, Electrolux, undertake that if, within 12 months * Products of Electrolux manufacture which are not of the date of the purchase, this Electrolux appliance marketed by Electrolux.
  • Page 11: Technical Data

    Instructions for the Installer Engineer technical data OVERALL DIMENSIONS SUPPLY CONNECTIONS Width: 580 mm. Gas: Depth: 510 mm. RC 1/2 inch (1/2 inch male) Rear right hand corner Height: 88 mm. Weight: 9,8 Kg. Electric: 230-240V 50Hz supply, 3 core flexible cable with CUT OUT DIMENSIONS non rewireable plug fitted with a 3 amp cartridge fuse.
  • Page 12: Important Safety Requirements

    Important safety requirements This hob must be installed in accordance with the Gas Location Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). The hob may be located in a kitchen, a kitchen/diner Detailed recommendations are contained in the or bed sitting room, but not in a bathroom or shower following British Standards Codes Of Practice: B.S.
  • Page 13: Installation

    Installation IMPORTANT This appliance must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored.
  • Page 14: Building In

    Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or It is also recommended to carry out the electrical drawer it will be necessary to fit a heat resistant board connection to the hob as shown in diagrams 1 and 2. below the base of the hob on the underside of the work surface.
  • Page 15: Electrical Connection

    Electrical connections Permanent Connection Any electrical work required to install this In the case of a permanent connection, it is necessary appliance should be carried out by a qualified electrician or competent person, in that you install a double pole switch between the accordance with the current regulations.
  • Page 16: Wiring Diagram

    Wiring diagram 1. TAPS IGNITOR SWITCHES 2. IGNITOR UNIT...
  • Page 17: Fault Finding

    Fault Finding Preliminary Electrical Systems Check PLUG (with cover removed) SOCKET (face view) Earth Wire Green/Yellow Blue Brown Green Yellow START Neutral Wire Isolate appliance Blue and carry out: A: Earth Continuity check. Blue Green Brown Yellow Carry out: Electricity supply Carry out: D: Resistance to should now be...
  • Page 18 Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse and Light burner manually replace if necessary Check by pass simmer Check polarity and earth adjusted continuity of supply point Check position of the Check earth continuity electrode of appliance...
  • Page 19: Commissioning

    Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
  • Page 20: Servicing

    Servicing A: Removal Of Hob Top D: Removal Of Burner 1. Remove the panstands and each burner cap and 1. Follow the procedures in Section A. crown. 2. With the aid of a 12mm spanner loosen off the pipe 2. Lift the hob from off the working top. connection nut.

This manual is also suitable for:

Ehg 679 w