Related Manuals for Electrolux EHG 672
Summary of Contents for Electrolux EHG 672
- Page 1 G a s H o b INSTRUCTION BOOKLET Models EHG 672 - EHG 674 - EHG 675 35670-2601...
-
Page 2: Important Safety Information
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 01635 522799 Installation This hob must be installed by qualified personnel, When using other electrical appliances, ensure the according to the manufacturer’s instructions and to cable does not come into contact with the hot the relevant British Standards. -
Page 3: Table Of Contents
Page 17 Spare Parts Page 8 Fault Finding Page 18 Guarantee Conditions Page 9 Commissioning Page 20 Electrolux Service Force Servicing Page 21 Centre Addresses Page 10 Conversion from natural gas to LPG Page 21 Guide to Use the instructions... -
Page 4: Description Of The Hob
Description of the Hob EHG 672 1. Hob Top 2. Rapid Burner EHG 674 3. Semi-rapid Burners EHG 675 4. Auxiliary Burner 5. Control knob for back right burner (semi-rapid) 6. Control knob for back left burner (semi-rapid) 7. Control knob for front left burner (rapid) 8. -
Page 5: Operation
Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite. If the control knobs become difficult to turn, please contact your local Electrolux Service Centre. -
Page 6: Maintenance And Cleaning
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. -
Page 7: Something Not Working
Your call will be routed to the Service Centre Customer Care Department covering your post code area. The addresses of Electrolux Electrolux Service Force Centres are detailed on the PO Box 47 following pages. Newbury RG14 5XL... -
Page 8: Guarantee Conditions
We, Electrolux, undertake that if, within 12 months * Products of Electrolux manufacture which are not of the date of the purchase, this Electrolux appliance marketed by Electrolux. or any part thereof is proved to be defective by any... -
Page 9: Electrolux Service Force
ELECTROLUX SERVICE FORCE To contact your local Electrolux Service Force Centre telephone 0990 929929 ISLE OF LEWIS ND Macleod NORTH EAST CHANNEL ISLANDS (M69) 16 James Street Stornoway GUERNSEY Guernsey Electricity GATESHEAD Unit 356a Isle of Lewis PO Box 4... - Page 10 ELECTROLUX SERVICE FORCE To contact your local Electrolux Service Force Centre telephone 0990 929929 MIDLANDS LONDON & EAST ANGLIA SOUTH EAST BIRMINGHAM 66 Birch Road East, CANVEY ISLAND 2-4 Sandhurst ASHFORD Unit 2 (M18) Wyrley Road Industrial Kings Road (M58)
-
Page 11: Technical Data
Instructions for the Installer Engineer technical data OVERALL DIMENSIONS SUPPLY CONNECTIONS Width: 580 mm. Gas: Depth: 500 mm. RC 1/2 inch (1/2 inch male) Rear right hand corner Height: 88 mm. Weight: 8 Kg. Electric: 230-240V 50Hz supply, 3 core flexible cable with CUT OUT DIMENSIONS non rewireable plug fitted with a 3 amp cartridge fuse. -
Page 12: Important Safety Requirements
Important safety requirements This hob must be installed in accordance with the Gas Location Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). The hob may be located in a kitchen, a kitchen/diner Detailed recommendations are contained in the or bed sitting room, but not in a bathroom or shower following British Standards Codes Of Practice: B.S. -
Page 13: Installation
Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. -
Page 14: Building In
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or It is also recommended to carry out the electrical drawer it will be necessary to fit a heat resistant board connection to the hob as shown in diagrams 1 and 2. below the base of the hob on the underside of the work surface. -
Page 15: Electrical Connection
Electrical connections Permanent Connection Any electrical work required to install this In the case of a permanent connection, it is necessary hob should be carried out by a qualified electrician or competent person, in that you install a double pole switch between the hob accordance with the current regulations. -
Page 16: Wiring Diagram
Wiring diagram 220/240 A. IGNITOR SWITCH B. IGNITOR UNIT... -
Page 17: Fault Finding
Fault Finding Preliminary Electrical Systems Check PLUG (with cover removed) SOCKET (face view) Earth Wire Green/Yellow Blue Brown Green Yellow START Neutral Wire Isolate appliance Blue and carry out: A: Earth Continuity check. Blue Green Brown Yellow Carry out: Electricity supply Carry out: D: Resistance to should now be... - Page 18 Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse and Light burner manually replace if necessary Check by pass simmer Check polarity and earth adjusted continuity of supply point Check position of the Check earth continuity electrode of appliance...
-
Page 19: Commissioning
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. -
Page 20: Servicing
Servicing A: Removal Of Hob Top D: Removal Of Burner 1. Remove all control knobs, pan supports, burner caps and crowns. 1. Follow the procedures in Section A. 2. Remove 2 screws from each burner. 2. With the aid of a 12mm spanner loosen off the pipe 3.