Electrolux EHG 673 Instruction Booklet
Gas hobs
Hide thumbs
Also See for EHG 673:
- Instruction booklet (17 pages) ,
- Instruction booklet (16 pages) ,
- Instruction booklet (16 pages)
Related Manuals for Electrolux EHG 673
Summary of Contents for Electrolux EHG 673
- Page 1 Gas hobs INSTR INSTR UCTION BOOKLET UCTION BOOKLET INSTR UCTION BOOKLET UCTION BOOKLET INSTR INSTR UCTION BOOKLET Please read this instruction booklet before using the appliance Mod. EHG 673 - EHG 691 35675-8204...
-
Page 2: Important Safety Information
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 950950 Installation Service This hob should only be repaired or serviced by an This hob must be installed by qualified personnel, authorised Service Engineer and only genuine according to the manufacturer’s instructions and to approved spare parts should be used. -
Page 3: Table Of Contents
Fault Finding Guarantee Conditions Commissioning Conversion from Natural Gas to LPG Description of the Hobs 1. Hob Top 2. Rapid Burner 3. Semi-rapid Burners 4. Auxiliary Burner 5. Control knobs 6. Electric Ignition Push Button (only for model EHG 673) -
Page 4: Operation
Operation Hob Burners To light a burner: To light a burner: Mod. EHG 673 Mod. EHG 691 push the electric ignition pushbutton which is marked push in the relevant control knob and turn it by a little spark; anticlockwise to maximum position. -
Page 5: Something Not Working
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. -
Page 6: Customer Care Department
Customer Care Department For general enquiries concerning your Electrolux appliance or for further information on Electrolux products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.electrolux.co.uk Customer Care Department ELECTROLUX 55-77 High Street Slough... -
Page 7: Instructions For The Installer
Instructions for the Installer Engineers technical data Overall dimensions Ignition HT Spark Spark Generator Ispra Control's BF 50066 - Width: 580 mm. 220-240V 0.6 VA T 120 Depth: 500 mm. Spark Gap Fixed Rear Left Burner (semi-rapid) Heat Input 2.0 kW (6824 BTU/HR) Cut out dimensions Width: 550 mm. -
Page 8: Important Safety Requirements
Important safety requirements This hob must be installed in accordance with the Gas FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. -
Page 9: Building In
Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to R FO 0814 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and A) End of shaft with nut installation. -
Page 10: Electrical Connections
Fitting the Hob into the worktop Carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out taking care that the seals meet without overlapping; • place the hob in the cut out, taking care that it is centred;... -
Page 11: Wiring Diagram
Wiring Diagram 220/240 A. IGNITOR SWITCH B. IGNITOR UNIT Fault Finding Preliminary Electrical Systems SOCKET PLUG (with cover (face view) removed) Check Earth Wire Green/Yellow Blue Brown Green START Yellow Isolate appliance and carry out: A: Earth Continuity Neutral Wire Blue check. - Page 12 Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse Light burner manually and replace if necessary Check polarity and Check by pass simmer earth continuity of adjusted supply point Check position of the Check earth continuity electrode of appliance...
-
Page 13: Commissioning
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. Turn the gas tap to the MAX position and ignite. Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. -
Page 14: Conversion From Natural Gas To Lpg
Conversion from Natural Gas to LPG To adjust the gas rate It is important to note that this model is designed for use with natural gas but can be converted for use with With the aid of a thin bladed screwdriver completely butane or propane gas providing the correct injectors tighten down the by pass adjustment screw. -
Page 16: Customer Care
CUSTOMER CARE Electrolux 55-77 High Street Slough Berkshire, SL1 1DZ Tel: 08705-950950 © Electrolux plc 2003 The Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx.