Your new Cooker Hood Using your new Cooker Hood is very simple. Nevertheless, to get the best results it is important that you read this handbook thoroughly before installing and using your appliance for the first time. Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local electricity company regulations.
Contents Page Electrical Requirements Get to know your Cooker Hood Installing your Cooker Hood Installation for Recirculation Installation for Extraction Mounting Height Mounting between Cabinets Fitting the Decor Panel Operating your Cooker Hood The Controls Do’s and Don’ts Caring for your Cooker Hood 11-12 Filters and their Replacement Cleaning...
Get to know your Cooker Hood. Unpacking Before installation, ensure that you have removed all packing pieces. Fitted Door (not supplied Door support Controls Filter Grille Light Grille release Dimensions Height 400mm (15 Width 600mm (23 Depth adjustable from: 270mm (10 in) up to 460mm (18in), excluding the decor panel thickness.
Installing your Cooker Hood Your new Cooker Hood can be installed either Installation for Extraction: for recirculation or extraction through an This method is recommended if at all possible. outside wall. (All fitting supplied) Fumes and grease laden air are drawn into the underside of the hood and expelled outside Installation for Recirculation: the kitchen.
Page 6
Installing your Cooker Hood Top or Rear Extraction Fig.4 Connect the ducting material onto the flange: blank off the aperture which is not required. The charcoal filter is not required when the hood is installed in the ducting cycle. To remove the grille turn the locks (Fig.5 B) and pull the grille out and downwards.
Installing your Cooker Hood MOUNTING Mounting between cabinets on the Wall: Your Cooker Hood is designed to fit between The hood may be fixed to any rigid vertical two wall cupboards 600mm apart and to take surface. If the hood can only be fixed to a a door panel measuring 400mm (min) to hollow construction plaster or partition board 600mm (max) in height, to match the adjacent...
Page 8
Installing your Cooker Hood Fixing the Hood to the Cupboards: Replace the visor with decor panel, inserting it Place the template on the side of the right first in the upper slides and then in the lower cupboard, so that the letter B aligns with the slides.
Installing your Cooker Hood Fitting the Decor Panel: The hood is designed to be fully integrated into the kitchen by fitting a decor panel onto the visor to match the adjoining kitchen cabinets. To fit the decor panel remove the complete visor assembly from the hood.
Operating your Cooker Hood The Controls Make sure that the Cooker Hood is wired in Work Top Illumination and the power supply is switched on. The lower slider (ON/OFF) enables you to The Cooker Hood functions are controlled by switch on the work top illumination. two slide switches located on the right hand side behind the visor.
Caring for your Cooker Hood Before doing any cleaning or replacing the fil- THE CARBON FILTER - ters or light bulb, always ensure that the elec- (Recirculation only) tricity supply to the Cooker Hood is switched The activated carbon filter absorbs odours ‘OFF’...
Caring for your Cooker Hood Cleaning: The exterior of the Cooker Hood should be cleaned regularly to keep it looking like new. Wipe over with a soft cloth, wrung out in warm water and dry with a clean soft cloth. Wear protective gloves.
Troubleshooting. First, don’t panic! Parts There may be nothing wrong at all. Look for Please remember your new appliance is a your problem below, then check the things we complex piece of equipment. suggest. More often than not, this will give you the answer to your problem, and you’ll be able ‘DIY’...
Republic of Ireland: (01) 842 6836 08701 54 64 74 For further product information All Creda Services are offered as an extra benefit and do not affect your statutory rights. General Domestic Appliances Limited, Morley Way, Peterborough, PE2 9JB Part No. FP078-01...
Need help?
Do you have a question about the CRN40 and is the answer not in the manual?
Questions and answers