Advertisement
Available languages
Available languages
Quick Links
Download this manual
See also:
Instruction Manual
Industrial
Commercial
Owner's Guide
• INSTALLATION
• OPERATION
• MAINTENANCE
• SERVICING
READ
AND
THIS INSTRUCTION
MANUAL
IMPORTANT
Note any damage on the freight bill, as any damage
claim must be filed with carrier.
Motor, Motor Pulley, Pump and Belt are sold
separately
SAVE
EVAPORATIVE AIR COOLER
MODELS
CS11/16, CD11/16
Date purchase: _____________________
Purchased from: ____________________
1
CD21
Manual part # 70888
REV. 1/06
Advertisement
Related Manuals for Essick CS11
Summary of Contents for Essick CS11
- Page 1 • OPERATION • MAINTENANCE • SERVICING EVAPORATIVE AIR COOLER READ SAVE MODELS THIS INSTRUCTION CS11/16, CD11/16 MANUAL CD21 IMPORTANT Date purchase: _____________________ Note any damage on the freight bill, as any damage Purchased from: ____________________ claim must be filed with carrier.
- Page 2 INSTALLATION OF EVAPORATIVE COOLERS PREPARATION 1. All electrical and duct work must comply with local and federal codes. 2. Make arrangements to get the cooler from ground to roof (crane, hoist, etc.). LOCATION 1. Cooler should not be mounted near exhaust openings or vent pipes where fumes and odors can be drawn into cooler. 2.
- Page 3 MOTOR PULLEY ADJUSTMENT Before installing the motor pulley, loosen the set screw on the back side of the pulley and turn the outside jaw of the pulley until it is fully closed. Position the set screw over the closest flat spot in the thread and then open the outside jaw of the pulley 4 or 5 turns. Position the set screw over the closest flat spot in the thread and retighten the set screw.
-
Page 4: Maintenance
Essick Air Products is not responsible for any damage occurring from the use of water softeners, chemicals, descale material, or if a higher horsepower motor than what Essick Air Products recommends is used in the unit. Essick Air Products is not responsible for the cost of service calls to diagnose cause of trouble, or labor charge to repair and/or replace parts. - Page 5 CS11/16, CD11/16 & CD21 REPLACEMENT PARTS / PIEZAS DE RECAMBIO To order replacement parts, please call “The Cooler Hotline” at 1-800-643-8341. To ensure prompt service, have the following information available. Cooler Model #______________________________ Serial # ____________________________________ Manual # and Revision Date____________________ Purchased From_____________________________...
- Page 6 CS11/16, CD11/16 & CD21 REPLACEMENT PARTS / PIEZAS DE RECAMBIO CS11/16 CD11/16 & CD21 DESCRIPTION DESCRIPCIÓN PART NO. QTY. PART NO. QTY. ITEM NO. DE REF. CAN. NO. DE REF. CAN. FRONT FRENTE 70697 BOTTOM BANDEJA INFERIOR 70702 70681 BLOWER HOUSING...
- Page 7 • OPERACIÓN • MANTENIMIENTO • SERVICIO ENFRIADOR EVAPORATIVO CONSERVE MODELOS ESTE MANUAL DE CS11/16, CD11/16 INSTRUCCIÓN CD21 IMPORTANTE Fecha de compra: _____________________ Anote cualquier daño en el recibo del transporte. Cualquier demanda de daños por transporte se debe Comprado de: ____________________ presentar directamente con la compañía de...
- Page 8 INSTALACIÓN DEL ENFRIADOR EVAPORATIVO PREPARACIÓN 1. Todo el trabajo eléctrico y de los conductos debe cumplir con los códigos locales y federales. Haga los arreglos necesarios para subir el enfriador al techo (grúa, polea, etc.). UBICACIÓN 1. No instale el enfriador cerca de salidas de extractores o de tubos de ventilación para evitar que los humos y los olores penetren el enfriador.
- Page 9 AJUSTES DE LA POLEA DEL MOTOR Antes de instalar la polea del motor, afloje el tornillo de fijación en la parte interna de la polea y gire la parte exterior de la polea hasta que quede completamente cerrada. Coloque el tornillo de fijación en la superficie plana más cercana en la rosca y luego gire 4 o 5 vueltas la parte exterior de la polea.
-
Page 10: Mantenimiento
Essick Air Products para esta unidad. Essick Air Products no es responsable por el costo de las visitas de servicio para diagnosticar la causa del problema, o los costos por la mano de obra para reparar y/o reemplazar piezas.