Maintenance - Dimplex DS5598 Service Manual

②
Set the 3 Position Switch to the Remote position (refer to
Operation Section).
③
Wait a minimum of five (5) seconds and then turn the
main power ON.
④
Within 10 seconds of re-acquiring power, press the ON
button located on the remote control.
! NOTE: You will have only 10 seconds to perform this last
step. Failure to do so will result in these steps needing to
be followed again.
This will synchronize the remote control and receiver.
Battery Replacement
①
Slide battery cover open on the remote control
②
Correctly install one (1) 12 Volt (A23) battery in the battery
holder.
③
Close the battery cover.
Battery must be recycled or disposed of properly.
Check with your Local Authority or Retailer for recy-
cling advice in your area.

Maintenance

WARNING: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of fire, electric
shock or damage to persons.
Light Bulb Replacement
CAUTION: Allow at least five (5) minutes for light bulbs to
cool off before touching bulbs to avoid accidental burning of
skin.
Light bulbs need to be replaced when you notice a dark
section of the flame or when the clarity and detail of the log
exterior disappears. There are two bulbs under the log set
which generate the flames and embers.
Tool Requirements: Phillips screw driver
Helpful Hints: It is a good idea to replace all light bulbs at
one time if they are close to the end of their rated life. Group
replacement will reduce the number of times you need to
open the unit to replace light bulbs.
Upper Light Bulb Requirements: Quantity of one (1) clear
chandelier or candelabra bulbs with an E-12 (small) socket
base, 7 Watt rating.
Upper Bulb Replacement
1. Open door by pulling the handle.
2. Locate the upper bulb bracket.Bend light retainer bracket
down.Locate and remove the light bulb.Insert new bulb.
3. Bend light retainer bracket back into its original position.
4. Close the door.
Lower Light Bulb Requirements: Quantity of two (2) clear
chandelier or candelabra bulbs with an E-12 (small) socket
base, 60 Watt rating.
Lower Bulb Replacement
1. Open door by pulling the handle.Remove the screw from
the log set located in the center of the ember bed and
remove the log set from the unit.
2. Locate and examine the bulbs to determine which bulb(s)
required replacement.
3. Locate and remove the light bulb(s).
4. Insert new bulb(s).
5. Install the log set into the unit, pushing firmly against the
glass. Replace the log set retaining screw into the ember
bed.
6. Close the door.
Glass Cleaning
The clear door is cleaned in the factory during the assembly
operation. During shipment, installation, handling, etc., the
(Figure 4).
clear door may collect dust particles, these can be removed
by dusting lightly with a clean dry cloth.
To remove fingerprints or other marks, the clear door can
be cleaned with a damp cloth. The clear door should be
completely dried with a lint free cloth to prevent water spots.
To prevent scratching, do not use abrasive cleaners or spray
liquids on the clear door surface.
Plastic Door Cleaning
To remove fingerprints or other marks, the clear door can
be cleaned with a damp cloth. The clear door should be
completely dried with a lint free cloth to prevent water spots.
To prevent scratching, do not use abrasive cleaners or spray
liquids on the clear door surface.
Brass Door Cleaning
To remove fingerprints or other marks, the clear door can
be cleaned with a damp cloth. The clear door should be
completely dried with a lint free cloth to prevent water spots.
To prevent scratching, do not use abrasive cleaners or spray
liquids on the clear door surface.
Nickel Door Cleaning
To remove fingerprints or other marks, the clear door can
be cleaned with a damp cloth. The clear door should be
completely dried with a lint free cloth to prevent water spots.
To prevent scratching, do not use abrasive cleaners or spray
liquids on the clear door surface.
Stove Surface Cleaning
Use warm water only to clean painted surfaces of the
Compact Stove. Do not use abrasive cleaners.
Servicing
WARNING:
and cleaning described above, an authorized service
representative should perform any other servicing.
4
Except for light bulb replacement