Integra DTR-70.4 Instruction Manual page 63

Speaker Settings
If you change these settings, you must run
Audyssey MultEQ ® XT32 Room Correction and
Speaker Setup again (➔ page 38).
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
"Speakers Type(Front)" setting. For details on speaker
wire connection, see "Bi-amping the Front Speakers"
(➔ page 14). When connecting speakers without
crossover network, you need to change the "Speakers
Type(Front)" setting beforehand. For details on
connection, refer to "Using Speakers Without Crossover
Network" (➔ page 14).
Note
• When bi-amping is used, the AV receiver is able to drive up to 7.2
speakers in the main room.
• Before you change these settings, turn down the volume.
■
Speaker Impedance
4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
6ohms:
Select if the impedances of all speakers are between 6
and 16 ohms.
■
Speakers Type(Front)
Normal:
Select this if you've connected your front speakers
normally.
Bi-Amp:
Select this if you've bi-amped your front speakers.
Digital Crossover:
Select this if you're using speakers without crossover
network.
Tip
• If "Speakers Type(Front)" is set to "Digital Crossover", a
confirmation screen appears. Select "Next (2-7. Digital
Processing Crossover Network)" to display the screen for
Digital Processing Crossover Network (➔ page 67). Continue
with the settings.
■
Passive Subwoofer
Yes:
Select this if you've connected passive subwoofers.
No
■
Powered Zone 2, Powered Zone 3, Powered
Zone 4
No
Yes:
Zone 2/3/4 speakers can be used. (Powered
Zone 2/3/4 enabled).
■
11ch Playback
No
Yes
For 11.2-channel playback, set this setting to "Yes". If you
select front wide speakers setting in Speaker Configuration
is set to "None", it will be automatically switched to
"80Hz (THX)".
Note
• If the "Speakers Type(Front)" setting is set to "Bi-Amp" or
"Digital Crossover", passive subwoofer cannot be used.
• Powered Zone 3 is not available in the following cases:
– The "Speakers Type(Front)" setting is set to "Bi-Amp" or
"Digital Crossover".
– The "Passive Subwoofer" setting is set to "Yes".
– The "Powered Zone 2" setting is set to "No".
• Powered Zone 4 is not available in the following cases:
– The "Speakers Type(Front)" setting is set to "Bi-Amp" or
"Digital Crossover".
– The "Passive Subwoofer" setting is set to "Yes".
– The "Powered Zone 3" setting is set to "No".
• When the "Powered Zone 3" setting is set to "Yes"
(➔ page 63) while Powered Zone 2 is enabled (➔ page 86),
the surround back speakers cannot be used.
En-63
Advanced Operations
• When the "Powered Zone 2" setting is set to "Yes", the front
wide speakers cannot be used.
• When the "Powered Zone 3" setting is set to "Yes", the front
high speakers cannot be used.
• When the "Powered Zone 4" setting is set to "Yes", the surround
back speakers cannot be used.
• "11ch Playback" is not available in the following cases:
– The "Speakers Type(Front)" setting is set to "Bi-Amp" or
"Digital Crossover".
– The "Passive Subwoofer" setting is set to "Yes".
– The "Powered Zone 2" setting is set to "Yes".
– The "Zone 2 HDMI" setting is set to "Use".
• If the "11ch Playback" setting is set to "Yes", the audio of front
wide channel is output from FRONT WIDE PRE OUT only.