Integra DTR-50.4 Instruction Manual page 75

■
Audio Return Channel (ARC)
Off
Auto:
The audio signal from your TV tuner can be sent to
HDMI OUT MAIN of the AV receiver.
The audio return channel (ARC) function allows an ARC
capable TV to send the audio stream to HDMI OUT MAIN
of the AV receiver. To use this function, you must select
the TV/CD input selector and your TV must be ARC
capable. Default setting: " "
- - - -
Note
• This setting is fixed to "- - - -" when the "HDMI
Control(RIHD)" setting is set to "Off".
• This setting is set to "Auto" automatically when the "HDMI
Control(RIHD)" setting is set to "On" for the first time.
• If you set "Audio Return Channel" to "Auto", the "Audio
Selector" settings of the TV/CD input selector will be
automatically switched to "ARC" (➔ page 70).
After changing the settings of the "HDMI
Control(RIHD)", "HDMI Through" or "Audio
Return Channel", turn off the power on all connected
pieces of equipment and then turn them on again. Refer
to the user's manuals for all connected pieces of
equipment.
■
Lip Sync
Off
On
This function allows the AV receiver to automatically
correct any delay between the video and the audio, based
on the data from the connected monitor.
Note
• This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
■
InstaPrevue
These settings apply to "InstaPrevue" of the Home menu
and specify the preview display of HDMI
(➔ page 45)
video streams.
Sub Window
Multi:
Displays preview thumbnails all at once.
Single:
Displays preview thumbnails one-by-one.
With this setting, you can set the number of preview
thumbnails displayed.
Position
(with "Sub Window" set to "Multi")
Top, Bottom, Left, Right
(with "Sub Window" set to "Single")
Upper Left, Upper Right, Lower Left, Lower Right
With this setting, you can set the position of preview
thumbnails on the TV screen.
Note
• Depending on video signals, the picture may not be properly
rendered on the preview thumbnails of InstaPrevue.
Auto Standby
■
Auto Standby
Off
On
When "Auto Standby" is set to "On", the AV receiver
will automatically enter standby mode if there is no
operation for 30 minutes with no audio and no video signal
input.
"Auto Standby" will appear on the AV receiver's display
and OSD 30 seconds before the Auto Standby comes on.
Default setting: On (Australian models), Off (North
American models)
Note
• Set to " On" , the Auto Standby function may activate itself during
playback with some sources.
• The Auto Standby function does not work when Zone 2/3 is on.
En-75
Advanced Operations
Network
After modifying the network settings, you must confirm
the changes by executing "Save".
This section explains how to configure the AV receiver's
network settings manually.
If your router's DHCP server is enabled, you don't need to
change any of these settings, as the AV receiver is set to
use DHCP to configure itself automatically by default (i.e.,
DHCP is set to "Enable"). If, however, your router's
DHCP server is disabled (you're for example using static
IP), you'll need to configure these settings yourself, in
which case, a knowledge of Ethernet networking is
essential.
What's DHCP?
DHCP (Dynamic Host Configuration Protocol) is used by
routers, computers, the AV receiver, and other devices to
automatically configure themselves on a network.
What's DNS?
The DNS (Domain Name System) translates domain
names into IP addresses. For example, when you enter a
domain name such as www.onkyousa.com in your Web
browser, before accessing the site, your browser uses DNS
to translate this into an IP address, in this case
63.148.251.142.
■
MAC Address
This is the AV receiver's MAC (Media Access Control)
address. This address cannot be changed.