Integra DTR-40.4 Instruction Manual page 56

Speaker Distance
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup (➔ page 34).
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener's ears as the sound designer intended.
■
Unit
feet:
Distances can be set in feet. Range: 0.2ft to 30.0ft in
0.2 foot steps.
meters:
Distances can be set in meters. Range: 0.06m to
9.00m in 0.06 meter steps.
(The default setting varies from country to country.)
■
Left, Front Wide Left, Front High Left, Center,
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right, Surround
Back Left, Surround Left, Subwoofer
Specify the distance from each speaker to your
listening position.
Note
• Speakers that you set to "No" or "None" in
"Speaker Configuration" cannot be selected (➔ page 55).
• When the "Powered Zone 2" setting is set to "Yes"
(➔ page 54) and Zone 2 is turned on (➔ page 71), the
surround back and front high speakers cannot be used.
• When the "Powered Zone 3" setting is set to "Yes"
(➔ page 54) and Zone 3 is turned on (➔ page 71), the
surround and surround back speakers cannot be used.
Level Calibration
® This setting is set automatically by Audyssey 2EQ Room
Correction and Speaker Setup (➔ page 34).
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
■
Left, Front Wide Left, Front High Left, Center
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right, Surround
Back Left, Surround Left
–12.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
■
Subwoofer
*1
–15.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
Note
• These settings cannot be calibrated when the AV receiver is
muted.
• Speakers that you set to "No" or "None" in
"Speaker Configuration" cannot be selected (➔ page 55).
• When the "Powered Zone 2" setting is set to "Yes"
(➔ page 54) and Zone 2 is turned on (➔ page 71), the
surround back and front high speakers cannot be used.
• When the "Powered Zone 3" setting is set to "Yes"
(➔ page 54) and Zone 3 is turned on (➔ page 71), the
surround and surround back speakers cannot be used.
• The test tone is output at the standard level for THX, which is
0 dB (absolute volume setting 82). If you normally listen at
volume settings below this, be careful because the test tone will
be much louder.
*1
For the center speaker and subwoofer, the level settings made
by using the Quick Setup are saved in this menu (➔ page 48).
Tip
• If you're using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
En-56
Equalizer Settings
With the Equalizer settings, you can adjust the tone of
speakers individually with a 5-band equalizer. The volume
of each speaker can be set (➔ page 56).
■
Manual Equalizer
On:
You can adjust the equalizer for each speaker
manually. Continue with the following procedure:
,
*1
1
Press to select "Channel", and then use
select a speaker.
2
Use / to select a frequency, and then use the
to adjust the level at that frequency.
The volume at each frequency can be adjusted from
–6dB to 0dB to +6dB in 1 dB steps.
Tip
• You can select: "63Hz", "250Hz", "1000Hz", "4000Hz", or
"16000Hz". And for the subwoofer, "25Hz", "40Hz",
"63Hz", "100Hz", or "160Hz".
• Low frequencies (e.g., 63Hz) affect bass sounds; high
frequencies (e.g., 16000Hz) affect treble sounds.
3
Use to select "Channel", and then use
select another speaker.
Repeat steps 1 and 2 for each speaker.
You cannot select speakers that you set to "No" or
"None" in the "Speaker Configuration"
(➔ page 55).
Off:
Tone off, response flat.
Note
• When the Direct listening mode is selected, the equalizer settings
have no effect.
• If "Audyssey" is enabled, it prevails over this setting
(➔ page 60).
Advanced Operations
/ to
/
/ to