Craftmade Loris LO52 Installation Instructions

P.O. Box 1037
650 S. Royal Lane, Suite 100
Coppell, TX 75019
(800) 486-4892
8:00 to 5:00 CST (Central Standard Time)
Toll Free Fax: (877) 304-1728
email: customerservice@craftmade.com
www.craftmade.com
P. O. Box 1037
650 S. Royal Lane, Suite 100
Coppell, TX 75019 EE.UU.
(800) 486- 4892
8:00 a 5:00 CST (Hora local central)
Número de fax sin cargo: (877) 304-1728
Correo electrónico: customerservice@craftmade.com
www. craftmade.com
P. O. Box 1037
650 S. Royal Lane, Suite 100
Coppell, TX 75019 EE.UU.
de 8 heures à 17 heures (Heure standard du centre)
Numéro de télécopieur gratuit : (877) 304-1728
Email: customerservice@craftmade.com
www. craftmade.com
4
5
Installing Mounting Bracket
Support Beam
"J" Hook (S7)
Outlet Box
OUTLET BOX
Ceiling
Mounting Bracket (1)
Bracket Screws
& Washers (S3)
Wood Screws (S1)
Wood Screws (S1)
Canopy Screws
Locate downrod assembly (2). Loosen ball screw on black hanging ball to
free lock pin. Black hanging ball will slide down. Remove ground screw and
NOTE: Do not mount directly to sheet rock or ceiling tile.
green ground wire. Remove hanging ball from downrod and save all parts.
Prior to securing mounting bracket, screw "J" hook (S7) into ceiling outlet
box as a secondary support means. Secure mounting bracket (1) to the outlet
box by tightening bracket screws and washers (S3) as shown. If not mounting
to an outlet box, use wood screws and washers (S1) and mount securely to
Insert fan wires through threaded end of downrod.
ceiling beam.
10 11
Attach canopy (3) to the mounting bracket by placing screws into slot in
canopy. Twist clockwise to lock into place. Tighten screws rmly. Next, lock
the canopy ring into place at the bottom of the canopy.
Assemble blade arms to blade arm ywheel with the 6 motor screws (S9)
provided. Repeat for all blade arms. Assemble blade arm ywheel to fan
motor with 10 motor screws (S9) provided. Tighten screws securely.
NOTE: Depending on downrod length and ceiling clearance, it may be
necessary to assemble blades to blade arms (Step 12) prior to attaching
blade arm ywheel to fan motor.
1
L o r i s
Read and Save
1. Turn off electricity at main switch before wiring or servicing fan in order to avoid
possible electrical shock.
C e i l i n g F a n
2. All wiring must be in accordance with the National Electric Code (ANSI/NFPA70-1999) and local
electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. After making the wire connections, the wires should be spread apart with the grounded
conductor and the equipment-grounding conductor on the one side of the outlet box
and the ungrounded conductor on the other side of the outlet box.
4. e splices after being made should be turned upward and pushed carefully up into the outlet box.
5. Conductor of a fan identified as grounded conductor to be connected to grounded conductor of
power supply, conductor of a fan identified as ungrounded conductor to be connected to an
ungrounded conductor of power supply, conductor of fan identified for equipment grounding to be
connected to an equipment-grounding conductor.
6. Fan should not be mounted in an area where it might get wet.
7. WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked
"Acceptable for Fan Support" and use mounting screws provide with the outlet box.
e outlet box and its support must be able to support the moving weight of the fan (at least 35lbs).
8. For safety and best operating results, we recommend that you have a qualified
electrician assemble and install your fan.
9. WARNING: To reduce the risk of fire or electric shock, use the fan only with solid state speed control
device provided.
10.WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing
the brackets, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
11.Net Weight: e weight of the complete fan, including assembly hardware is ??? lbs.
Problem A: Fan Will not Start
Remedies:
1. Check fuse or circuit breaker and replace if necessary
2. Turn off electrical power and check all wire connectors.
3. Check on/off TCS and wall control selector switch. See operation instructions.
Problem B: Fan is Excessively Noisy
Installation Instructions
Remedies:
1. Check that all screws in fan assembly are tight and properly seated.
Instrucciones de instalación
2. Check to make sure mounting bracket is installed properly.
Instructions d'installation 3. Check to make sure light kit and glass are installed properly and tight.
4. If wall control is used, insure the wall control is not a transformer or a variable speed type.
Problem C: Fan Wobbles
Remedies:
1. Check that all blades are screwed firmly into blade holders.
2. Check that all blade holders are screwed firmly into motor.
3. Check the weight of blades. All our blades are weighed on electronic scales.
marked on the reverse side of the fan blade near the motor end. All of the blades should be
the same weight to prevent fan from wobbling.
4. A balancing kit is enclosed if needed.
6
Downrod Assembly
read the downrod onto the motor housing making sure the wires don't get
twisted. Insert safety bolt (S6) through ange and downrod and attach nut.
Tighten rmly. Tighten top set screw against downrod.
WARNING: Failure to completely tighten downrod as described in
steps above could result in the fan loosening and possibly falling.
12
Blade Arm Assembly
Align holes of blade arm to blade, assemble blade to blade arm with screws
(S4) provided and tighten securely, repeat for all blades.
2
ese Safety Precautions
Before Assembly
1. Make sure that the fan voltage (120) is compatible with your own electrical
system.
2. Check to make sure that your carton contains all the parts mentioned in the
parts list.
NOTE: e box can be used as a work space to prevent any damage on the
ornamental surface.
CAUTION: Before installing, choose a location for mounting the fan where the
blades have at least 7 feet of clearance from all objects and oor. Mount an
outlet box to the ceiling or use an existing box
CAUTION: Do not mount fan to sheet rock or drywall type materials. To
insure proper support, use the two #1 wood screws to secure mounting bracket
to joist or beam. If the location you choose does not have a suitable support
beam, install a 2"x 4" brace between ceiling joists to support.
Screw Package
Trouble Shooting Quantity
Hardware
S1. Wood Screws and Washers
2
Inventory
S2. Screws (for Canopy) 3
S3. Bracket Screws & Washers 2
S4. Blade Screws 10
S5. Wire Connectors 3
S6. Safety Bolt & Nut 1 S4 S9
S3
S7. "J" Hook 1
S8. Zip Tie 1
S9. Motor Screws 17
Tools you Need
e weight is
1. Phillips Screwdriver 2. Adjustable Wrench 3. Flat Screwdriver
7
Place ange cover, canopy ring and canopy in order over downrod assembly.
Replace hanging ball, insert hanging pin through downrod and tighten set
screw though hanging ball into downrod.
WARNING: Failure to completely tighten downrod as described in
steps above could result in the fan loosening and possibly falling.
13
Light Kit Assembly
Connect light kit wires to motor housing. Attach light kit to
mounting plate with 3 screws provided. Tighten screws securely.
3
What You Have
Parts Quantity
1. Mounting Bracket 1
2. Down Rod Assembly 6" Rod 1
3. Canopy 1
4. Canopy Ring 1
5. Flange Cover 1
6. Fan Housing & Motor 1
7. Blade Arm Flywheel 1
8. Light Kit 1
9. Blade Arms 3
10. Blades 3
11. Glass Bowl 1
12. Bulb 1
13. Universal Remote Control 1
S2
S5 S6
S7
S1 S8
13
4.Wire Strippers
8
Lift fan onto the mounting bracket (1). Turn housing until hanging ball seats
itself into ball socket (listen for click).
For added security, attach safety cable from fan unit to "J" hook (S7) in outlet
box. Secure by looping zip tie (S8) through safety cable and "J" hook. Tighten
zip tie securely.
WARNING: To reduce the risk of re, electric shock or personal injury,
mount to outlet box marked "acceptable for fan support" and use mounting
screws provided with the outlet box. Most outlet boxes commonly used for
the support of lighting xtures are not acceptable for fan support and may
need to be replaced. Consult a quali ed electrician if in doubt.
Install halogen light bulb into fan. Screw bulb firmly into socket.
Install glass bowl, twist into place.
3
Turn o circuit breakers and wall switch to the fan supply line leads.
1
Important: When using an existing outlet box, be sure the box is
Preparation
securely attached to the building structure and can support the full
2
weight of the fan. Failure to do so can result in serious injury or death.
3
4
a.) Downrod Mount b.) Angle Mount
5
(Normal Ceilings) (Vaulted Ceilings)
6
IMPORTANT: If using the angle mount method, check to make sure the ceiling angle is
not steeper than 35º. Angles greater than 35º will require a 45º angle adapter.
7
8
30"
9
84"
10
11
• Check to make sure blades are at least 30" from any obstruction.
12
• Check Down rod Length to make sure blades are at least 7' above the floor.
8
Wiring
Ground
1. Connect fan wires to ceiling
Wire
White (Neutral)
Connectors wires: white fan wire to white
(S5)
outlet wire, black to black and
Black
(Power) green to green. Wire connectors
(S5) are provided for your
Ground
White (Green)
convenience. If an additional blue
Black
wire is present then also connect
Blue
the blue wire to the black wire.
Outlet Box
Ground (Green)
2. After connections are made, turn
splices upward and push carefully
Downrod
Ground into outlet box. Separate blue and
(Green)
black wires on one side of the box,
and white and green wires on the
Mounting Bracket
Ground (Green)
other side.
ere are 4 colored wires coming from the top of the motor.
(including ground wire).
Remote Control Operation Instructions
ON/OFF For emergency shut off.
HIGH Controls fan motor speed. To select desired speed, press
MEDIUM button once and release.
LOW
REVERSE Controls direction of fan blades. To reverse fan blades, press
once and release.
FAN OFF Turns fan motor speed off. Press once to turn off. To start
motor speed again, hit one of the motor speed buttons.
L-1 Controls no function on this fan.
L-2 Controls the on/off and intensity for optional light kit. Push
and release for on/off function. Hold down for full range light
dimming.
NOTE: The "High", "Medium" or "Low" buttons may be used to start
the fan motor. The speed of the fan may be changed at anytime.