Confi Guring Home City Settings - Casio 3259 Operation Manual

Selecting a Mode
• The illustration below shows which buttons you need to press to navigate between modes.
To return to the Timekeeping Mode from any other mode, hold down D for about two seconds.
•
Data Recall Data Recall
Alarm Mode Alarm Mode Mode Mode
Countdown Countdown
Stopwatch Mode Stopwatch Mode Timer Mode Timer Mode
E-16
General Functions (All Modes)
The functions and operations described in this section can be used in all of the modes.
Direct Timekeeping Mode Access
To enter the Timekeeping Mode from any other mode, hold down D for about two seconds.
•
Auto Return Features
• The watch will automatically return to the Timekeeping Mode if you do not perform any button operation
for a particular amount of time in each mode.
Mode Name
Tide/Moon Data, Data Recall, Alarm, Digital Compass
Altimeter
Barometer/Thermometer
Setting screen (digital setting fl ashing)
• If you leave a screen with fl ashing digits on the display for two or three minutes without performing any
operation, the watch exits the setting screen automatically.
Initial Screens
When you enter the Data Recall, Alarm, World Time, or Digital Compass Mode, the data you were viewing
when you last exited the mode appears fi rst.
Scrolling
The A and C buttons are used on the setting screen to scroll through data on the display. In most
cases, holding down these buttons during a scroll operation scrolls through the data at high speed.
E-18
Confi guring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting either standard time or
daylight saving time (DST).
City code City code
To confi gure Home City settings
PM PM
Year Year
1. In the Timekeeping Mode, hold down E until SET Hold appears on
indicator indicator
Month Day Month Day
the display and then the city code starts to fl ash.
• The watch will exit the setting mode automatically if you do not
perform any operation for about two or three minutes.
• For details about city codes, see the "City Code Table" at the back
of this manual.
2. Use A (East) and C (West) to scroll through the available city codes.
• Keep scrolling until the city code you want to select as your Home
City is displayed.
Hour : Hour : Seconds Seconds
3. Press D to display the DST setting screen.
Minutes Minutes
DST indicator DST indicator
4. Press A to toggle the DST setting between Daylight Saving Time (ON)
and standard time (OFF).
• Note that you cannot switch between standard time and daylight
saving time (DST) while UTC is selected as your Home City.
E-20
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the Timekeeping Mode time and date settings if they are off.
To change the current time and date settings
1. In the Timekeeping Mode, hold down E until SET Hold appears on
PM PM City City
the display and then the city code starts to fl ash.
indicator indicator code code Year Year
Seconds Seconds
Hour : Minutes Hour : Minutes
Month Day Month Day
E-22
Operation Guide 3259
Timekeeping Mode Timekeeping Mode
Tide/Moon Data Tide/Moon Data
Mode Mode
World Time World Time
Mode Mode
Approximate Elapsed Time
3 minutes
1 hour minimum
24 hours maximum
24 hours
3 minutes
You can use buttons A, B, and C to enter a sensor mode directly from the Timekeeping Mode or
•
from another sensor mode. To enter a sensor mode from the Tide/Moon Data, Data Recall, Alarm,
Stopwatch, Countdown Timer, or World Time Mode, fi rst enter the Timekeeping Mode and then press
the applicable button.
Sensor Modes Sensor Modes
Digital Compass Mode Digital Compass Mode
Thermometer Mode Thermometer Mode
Timekeeping
Use the Timekeeping Mode (HOME) to set and view the current time and date.
Each press of E in the Timekeeping Mode will change screen contents as shown below.
•
• If you leave the Tide Graph on the display, it will automatically return to the year screen after about 24
hours.
Year Screen
Moon phase
Day of week
indicator
Year
Barometric
pressure
graph
Seconds
PM Hour :
indicator Minutes
5. After all of the settings are the way you want, press E to exit the setting screen.
To return to the screen in step 1, press E again.
•
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
Note
• After you specify a city code, the watch will use UTC* offsets in the World Time Mode to calculate
the current time for other time zones based on the current time in your Home City.
* Coordinated Universal Time, the world-wide scientifi c standard of timekeeping.
The reference point for UTC is Greenwich, England.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down E until SET Hold appears on
the display and then the city code starts to fl ash.
2. Press D to display the DST setting screen.
3. Press A to toggle the DST setting between Daylight Saving Time (ON)
and standard time (OFF).
4. After all of the settings are the way you want, press E to exit the
setting screen.
To return to the screen in step 1, press E again.
•
• The DST indicator appears to indicate that Daylight Saving Time is
DST indicator DST indicator
turned on.
2. Press D to move the fl ashing in the sequence shown below to select the other settings.
12/24-Hour
City Code DST
Format
Thermometer/Barometer/ Power Illumination
Altitude unit Saving Duration
• The following steps explain how to confi gure timekeeping settings only.
3. When the timekeeping setting you want to change is fl ashing, use A and/or C to change it as
described below.
Screen To do this:
Change the city code
Toggle between Daylight Saving Time (ON) and
Standard Time (OFF).
Toggle between 12-hour (12H) and 24-hour (24H)
timekeeping.
Reset the seconds to 00
(If the current seconds count is between 30 and 59,
one is added to the minute count).
Change the hour or minutes
Change the year, month, or day
Barometer/ Barometer/
Altimeter Mode Altimeter Mode
Tide Graph Screen
Tide graph
Month Day
Seconds Hour Minutes
Button Operation
Day
Tone On/Off
Do this:
Use A (East) and C (West).
Press A.
Press A.
Press A.
Use A (+) and C (–).
E-17
E-19
E-21
Year
Month
E-23