Inteli•Touch Operation - Casablanca MISSION Owner's Manual

INTELI•TOUCH OPERATION POWER
The POWER button is normally left in the on position. Always turn the power
off during cleaning or servicing the fan and during thunderstorms. It is also used
to exit or enter additional programs.
POWER must be left on to retain a previously set fan speed or light level.
INTELI•TOUCH OPERATION SPEED CONTROL
There are six individual speed settings for the fan; each speed is indicated
by an audible tone of increasing pitch.
To select the desired fan speed:
1. With fan off, press and hold the button labeled
will start rotating at the slowest speed, and will increase in steps.
2. Release the button when the desired speed is reached.
The fan speed is now in memory and will automatically come on at the same
speed each time the
FAN
turn the fan on by pressing
turn fan off, then on by pressing and holding the
desired speed is reached. When the fan is on, you may increase the speed by
pressing and holding the
then release it.
INTELI•TOUCH • REVERSING AIRFLOW
The direction of airfl ow can be changed from downward to
upward or from upward to downward.
To reverse the airfl ow:
1. Make sure the
FAN
FAN
2. Press the button.
REVERSE
To turn the lights off and on, press and release the
than one second.
To vary the light brightness:
1. With lights off, press and hold the
lights come on at their lowest level and gradually become brighter.
2. Release the button when the desired brightness level is reached.
The brightness level is now in the fan memory and will automatically come
on at the same brightness the next time the
maintain this level of brightness, press the
one second. To lower the brightness, turn the lights off, then press and hold
the LIGHT button until the desired brightness level is reached. When the
light is on, you may increase the brightness level by pressing and holding
the button until the desired level is reached, then release it.
LIGHT
AUTOMATIC DEMONSTRATION PROGRAM
Programmed into every Inteli-Touch Series fan is an Automatic
Demonstration Program. It can be used to fully demonstrate and
test the operation of the fan.
To enter the demonstration program:
1. Turn POWER off for at least three seconds. This will clear
POWER
the fan memory ready for programming.
2. Turn POWER on.
POWER
3. Immediately operate the buttons in the following sequence:
+ +
LIGHT
FAN
FAN
FAN
button is used. To maintain this level of speed,
less than one second. To lower speed,
FAN
FAN
button until the desired speed is reached,
FAN
is on.
INTELI•TOUCH LIGHT
LIGHT
button. After one second the
LIGHT
LIGHT
button for less than
LIGHT
+ +
LIGHT FAN
FAN
Inteli•Touch
FAN CONTROL
. The fan blades
A momentary press
of the FAN button
TO CHANGE SPEED
Press and hold FAN
button longer than
button until the
Note: A four-toned signal indi-
cates the command was accepted
by the fan. A few seconds later
the fan will slow to a stop and
then reverse direction.
button for less
LIGHT CONTROL
A momentary press of
the LIGHT button
TO CHANGE BRIGHT -
button is used. To
PRESS AND HOLD
LIGHT BUTTON
LONGER THAN ONE
A multi-tone signal will verify the start of the test program which
proceeds as follows:
• Lights slowly increase to full intensity.
• Fan accelerates to speed three with audio tones.
• Light dims to half intensity.
• Fan accelerates to full speed with audio tones.
• Fan reverses at full speed with audio tones.
• Fan operates at full speed.
• Fan power is reversed with audio tones.
• Fan turns off with audio tones (blades coast for a short time).
• Lights turn off.
The complete cycle lasts slightly over one minute. It will continue
to repeat until the POWER is turned off for more than three
POWER
seconds, cancelling the program.
ON - OFF
one second
ON - OFF
NESS
SECOND
®
13