Sharp MD-X60H Service Manual page 34

MD-X60H
EON summary no™tice for reference
1. EON-TI/PTY EON stand-by can be set, only when EON ind. lights up.
While EON ind. goes out (NO EON STATION), EON stand-by can't be set.
If the EON button is pressed, then "NO EON" is indication the display.
2. EON-TI/PTY Even if switch back ON TN station continue to keep EON stand-by.
3. EON-TI Don't switch TN ON during TN broadcast TA. (same item)
4. EON-TI/PTY EON can be cancelled during receiving ON station by pressing EON button if necessary and
switch back ON TN.
5. EON-TI/PTY EON stand-by is perfectly cancelled (cleared) by pressing EON button 2 times during stand-by or powerOFF
or Tun Up/
6. EON-TI/PTY After setting EON stand-by, stand-by items can be confirmed by pressing EON button one time.
7. EON-TI/PTY EON button function:
8. EON-TI/PTY After setting EON-TI and EON-PTY stand-by, if when EON data is not transmitted, EON ind goes out
and EON stand-by is automatically cancelled display "NO EON".
9. EON-TI EON-TI stand-by can't be set. When TP=0,TA=0(TN) even if EON ind. lights up and the EON
button is
10. EON-PTY Don't switch TN ON during TN broadcast same specified PTY. (same item of PTY)
11. EON-TI/PTY Switch TN ON
Never switch TN ON1 ON2
12. EON-TI/PTY After switch TN ON station. When ON station is NO RDS, NO
items.
The receiver switch back ON TN displaying "NO READY".
13. During receive ON station. when ON station become to be NO RDS, NO signal, TA=ON to OFF or
14. EON-TI/PTY Switch TN ON in case of 2 more stations exist, comparing field strength and switch to the
station, if these signals are same strength, switch to the first previous station.
If same frequency as AF'Sexists in the preset memory, then switch TN ON (preset memory
station)
In case of exist 2 more preset memories of AF'S,
EON DATA
15. Even if switch TN ON preset memory straight, that ON station is very weak signal, then search
another
Of all atations
automatically display "NO
16. EON-TI/PTY No linkage volume, power ON/OFF, and switch function.
About the TP and TA indicators
TP indicator
Not lit (OFF)
Not lit (OFF)
Lit (ON)
Lit (ON)
Down or change band or recall pre-set CH.
•EON setting
•Confirm stand-by items
•Cancel (ON TN)
•EON clear cancel (2 times)
pressed then "NO TI" is indication the display.
TN station one cycle.
Other net to other net station.
different PTY item, The receiver switch back ON TN.
straight.
first, also in this case no concern to field strength.
AF'S (ON) station comparing field strength and switch to the strongest station as a result.
of AF'S are very weak or no good condition, then, switch back ON TN
READY".
TA indicator Meaning
Not lit (OFF) This programme does not carry traffic announcements nor does
it refer, via EON, to a programme that does.
Lit (ON) This programmecarries EON information about another
programme which gives traffic information.
Not lit (OFF) This programme carries traffic announcements but none are
being broadcast at present and may also carry EON information
about other traffic announcements.
Lit (ON) A traffic announcement is being broadcast on this programme at
present.
– 34 –
signal, TA=OFF or different PTY
then switch to the preset CH which taken in
strongest