Table of Contents
Advertisement
Quick Links
V6FP/V6FU
USER'S MANUAL
M/B For Socket-A Athlon/Duron Processor
NO. G03-V6FPR3A
Release date: June 2003
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject
to change at any time without notice, and should not be construed as a commitment by manufacturer.
Advertisement
Table of Contents
Related Manuals for JETWAY V6FP
Summary of Contents for JETWAY V6FP
- Page 1 V6FP/V6FU USER'S MANUAL M/B For Socket-A Athlon/Duron Processor NO. G03-V6FPR3A Release date: June 2003 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
-
Page 2: Table Of Contents
TABLE OF CONTENT USER’S NOTICE ......................ii MANUAL REVIS1ION INFORMATION ................ii COOLING SOLUTIONS ....................ii CHAPTER 1 INTRODUCTION OF V6FP/V6FU MOTHERBOARD 1-1 FEATURE OF MOTHERBOARD................1 1-2 SPECIFICATION .....................2 1-3 PERFORMANCE LIST ...................3 1-4 LAYOUT DIAGRAM & JUMPER SETTING ............4 CHAPTER 2 HARDWARE INSTALLATION 2-1 HARDWARE INSTALLATION STEPS ..............6... -
Page 3: User's Notice
TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE V6FP/V6FU MOTHER-BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. -
Page 4: Chapter 1 Introduction Of V6Fp/V6Fu Motherboard
A series CPUs based system, by integrating a high performance North Bridge, advanced hardware 2D/3D GUI engine and Super-South Bridge. The V6FP/V6FU provided 2 pcs DDR Module Socket support DDR 200/266 SDRAM and 2 pcs SDR Module support PC100/PC133 SDRAM . -
Page 5: Performance List
Spec Description ∗ Micro ATX form factor 4 layers PCB size: 24.4x24.4cm Design ∗ VIA VT 8375 (KM266) Memory Graphic Host Chipset Chipset ∗ VIA VT8235 South Bridge Clock Generator ∗ Support 200/266MHz (100/133MHz) Front Side Bus Clock (CPU Bus clock) ∗... -
Page 6: Layout Diagram & Jumper Setting
The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report CPU:... - Page 7 PRINT GAME/MIDI PORT PS/2 Mouse PS/2 Keyboard COM1 LINE-IN LINE-OUT K/B Power ON CPU Socket Jumper (JP1) CPU FAN PS2 KB/Mouse Port ATX Power Connector USB Port SDR Socket X2 FAN2 PC99 Back Panel DDR Socket X2 VIA KM266 (VT8375) Chip ATA 133 IDE Connector...
-
Page 8: Expansion Sockets
PS/2 Mouse & PS/2 Keyboard 6-pin Female P.12 Connector USB Port Connector 4-pin Connector P.12 RJ-45 LAN Port Connector RJ-45 Connector P.12 (for V6FP) PARALL Parallel Port Connector 25-pin Female P.12 AUD _ GAME Audio/Game Connector 3 phone jack + 15-pin Connector P.12 COM1... -
Page 9: Hardware Installation Steps
Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard setting 2. Install CPU 3. Install Memory 4. Install Expansion cards 5. Connect Ribbon cables, Panel wires, and power supply 6. -
Page 10: Install Cpu
JBAT JBAT 1-2 closed Normal 2-3 closed Clear CMOS CMOS RAM Clear Setting (3) Keyboard Power On function Enabled/Disabled (3-pin): JP1 When setting Enabled you can using keyboard by key in password to power on system. 1-2 closed K/B Power ON Disable 2-3 closed K/B Power ON Enabled (Default) -
Page 11: About Amd Athlon & Duron 462-Pin Cpu
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and establish the relationship between the various components. Driver - software, which defines the characteristics of a device for use by another device or other software. Processor - the "central processing unit"... -
Page 12: Install Memory
2-4 Install Memory This motherboard provides 184-pin DUAL INLINE MEMORY MODULES (DIMM) for DDR SDRAM and 168-pin DUAL INLINE MEMORY MODULES (DIMM) for SDR SDRAM sites for memory expansion available from minimum memory size of 64MB to maximum memory size of 2.0GB DDR/SDR SDRAM. Valid Memory Configurations Bank 184-Pin DIMM... -
Page 13: Expansion Card
2-5 Expansion Cards WARNING! Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2-5-1 Procedure For Expansion Card Installation 1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers. -
Page 14: Interrupt Request Table For This Motherboard
Interrupt request are shared as shown the table below: INT A INT B INT C INT D PCI slot 1 Shared PCI slot 2 Shared PCI slot 3 Shared ... - Page 15 The connectors for PS/2 keyboard and PS/2 Mouse. USB Port connector: USB The connectors are 4-pin connector that connect USB devices to the system board. LAN Port connector: LAN (only for V6FP) This connector is standard RJ45 connector for Network. Parallel Port Connector (25-pin female): PARALL Parallel Port connector is a 25-pin D-Subminiature Receptacle connector.
- Page 16 Pin 1 Floppy Drive Connector (10) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly.
-
Page 17: Headers
2-6-2 Headers (1) Line-In/Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-In, Line-out, MIC connector with cable. AUDIO Pin 1 AUD _ MIC AUD _ G ND AUD _ VCC AUD _ MIC _ BIAS AUD _ R ET _ R AUD _ FPO UT _ R HP _ O N AUD _ RET _ L... - Page 18 Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system’s power supply. See the figure below.
- Page 19 (11) FAN Headers (3-pin) : FAN1, FAN2, CPUFAN These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan’s plug to the board taking into consideration the polarity of connector.
-
Page 20: Starting Up Your Computer
1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used. -
Page 21: Entering Setup
Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. -
Page 22: The Main Menu
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. -
Page 23: Standard Cmos Features
Use this menu to load the BIOS default values that are factory settings for optimal performances system operations. Load Standard Defaults Use this menu to load the BIOS default values for the minimal/stable performance system operation. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. Save &... -
Page 24: Advanced Bios Features
Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use Manual to define your own drive type manually. - Page 25 Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
-
Page 26: Advanced Chipset Features
Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled. Typematic Rate (Chars/Sec) Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30. -
Page 27: Dram Timing Settings
Please refer to section 3-6-1 AGP Timing Settings Please refer to section 3-6-2 PCI Timing Settings Please refer to section 3-6-3 System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. -
Page 28: Agp Function Setting
If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. -
Page 29: Integrated Peripherals
3-7 Integrated Peripherals CMOS Setup Utility – Copyright(C) 1984-2003 Award Software Integrated Peripherals > OnChip IDE Function Press Enter Item Help > OnChip Device Function Press Enter > Onboard Super IO Function Press Enter Init Display First PCI Slot Menu Level > ↑↓→←... -
Page 30: Onchip Device Function
OnChip IDE Channal0/Channel1 The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. -
Page 31: Onboard Super Io Function
AC97 Modem Device This item allows you to decide to enable/disable the chipset family to support AC97 Modem. The settings are: Auto, Disabled. USB Host Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripherals. -
Page 32: Power Management Setup
Parallel Port Mode : Standard Parallel Port : Enhanced Parallel Port : Extended Capability Port SPP/EPP/ECP/ECP+EPP To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the onboard parallel port will operate in ECP mode only. -
Page 33: Wake Up Events
Modem Use IRQ This determines the IRQ in which the MODEM can use. The settings are: 3, 4, 5, 7, 9, 10, 11, NA. Power Button Function Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state. The settings are: Delay 4 Sec, Instant-Off. -
Page 34: 3-8-1.1 Irqs Activities
3-8-1.1 IRQs Activities CMOS Setup Utility – Copyright(C) 1984-2003 Award Software IRQs Activities Primary INTR Item Help IRQ3 (COM 2) Enabled IRQ4 (COM 1) Enabled IRQ5 (LPT 2) Enabled Menu Level >>> IRQ6 (Floppy Disk) Enabled IRQ7 (LPT 1) Enabled IRQ8 (RTC Alarm) Disabled... -
Page 35: Irq Resources
by a “>”). The settings are: Auto(ESCD), Manual. IRQ Resources When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. Please refer to section 3-9-1 PCI/VGA Palette Snoop Leave this field at Disabled. The settings are Enabled, Disabled. 3-9-1 IRQ Resources CMOS Setup Utility –... -
Page 36: Miscellaneous Control
This item can let users setting the Shutdown temperature, when CPU temperature over this setting the system will auto shutdown to protect CPU. Show PC Health in Post During Enabled, it displays information list below. The choice is either Enabled or Disabled Current CPU Temperature/Current System Temp/Current FAN1, FAN2 Speed/Vcore/ Vdd/3.3V/+5V/+12V/-12V/VBAT(V)/5VSB(V) This will show the CPU/FAN/System voltage chart and FAN Speed. -
Page 37: Load Standard/Optimized Defaults
Load Standard Defaults When you press <Enter> on this item, you get confirmation dialog box with a message similar Load Standard Defaults (Y/N)? N Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system operations. Load Optimized Defaults When you press <Enter>... -
Page 38: Magic Install Supports Windows 95/98/98Se/Nt4.0/2000/Xp
VIA 4 IN 1 install VIA Service Pack 4 IN 1 driver install VIA VGA driver SOUND install ALC AC97’ Codec Audio driver install VIA 10/100MB LAN Controller driver (Only for V6FP) USB2.0 install USB 2.0 driver DIRECTX8 install Microsoft DirectX 8.1 driver... -
Page 39: Via 4 In 1 Install Via Service Pack 4 In 1 Driver
AGPVXD : VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART.VXD WILL PROVIDE SERVICE ROUTINES TO YOUR VGA DRIVER AND INTERFACE DIRECTLY TO HARDWARE, PROVIDING FAST GRAPHIC ACCESS IRQ ROUTING : VIA PCI IRQ MINIPORT DRIVER IS TO BE INSTALLED UNDER WIN98 ONLY, IT WILL FIX PCI IRQ ROUTING SEQUENCE INF : VIA REGISTRY DRIVER IS TO BE INSTALLED UNDER WINDOWS... -
Page 40: Vga
7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer 4-2 VGA install VIA VGA Driver A. For WINDOWS 9X/ME/NT4.0/2000/XP 1. Click VGA when MAGIC INSTALL MENU Click NEXT When ProSavageDDR Driver appears Install Setup Wizard Appears... -
Page 41: Sound
For WIN98/NT4.0/WIN2K/XP is X:\CODEC\ALC\SETUP.EXE Note: In Win2K/WinME users have to click Control Panel\System\Device Manager\ DVD\CD-ROM drives to Enabled digital CD Audio for the CD-ROM Device when use the SPDIF-Out digital signal. 4-4 LAN Install VIA 10/100MB LAN Controller Drive r (for V6FP) -
Page 42: Pc-Health
The VIA 10/100MB PCI Ethernet Adapter Driver path is X:\VIA\LANDRV Click LAN when Magic Install Menu appear 2. Setup VIA 10/100Mb PCI Ethernet Driver Driver install Finish , Click Yes and Restart When windows ask VIA 10/100Mb PCI Computer Ethernet Adapter driver path, Change directory to X:\VIA\LANDRV and click OK , then finish installation 4-5 PC-HEALTH... -
Page 43: Hardware Doctor Monitoring Software
(Support Windows 9X/ME/2K/NT/XP) In Windows 95/98 Winbond Hardware Doctor Monitoring Software needs some system files to copy in Utility that’s why it needs install PC-HEALTH twice to complete setup. 1. Click PC-Health when Magic Install Menu 2. Click OK when Winbond Hardware Doctor appears Setup Window appears 3. - Page 44 Click Magic BIOS when Magic Install Click Next to install the Magic BIOS in MENU appears Destination Folder After finish Setup you will have a Magic Double click the Magic BIOS icon you will BIOS icon in your screen have this picture, choose from internet you can upgrade BIOS On-line When On-line update BIOS the program Click Next if you need update BIOS, after...
-
Page 45: Usb2.0
When choose From Local Driver to update 10. Choose the correct BIOS file to update BIOS BIOS, you must have the correct BIOS file in your Local Driver 4-7 USB2.0 Install VIA USB2.0 Device Driver 1. Click USB2.0 when MAGIC INSTALL 2. -
Page 46: Pc-Cillin
4-8 PC-CILLIN Install PC-CILLIN 2002 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2. (1) Click "Install PC-CILLIN" when PC- MENU appear CILLIN 2002 main menu appears, and Click NEXT when "Install Shield Wizard For PC- CILLIN 2002" (2) Click Open Manual. you can learn PC- CILLIN 2002 how to use 3. -
Page 47: How To Disable On-Board Sound
You may copy from DRIVER CD X:\FLASH\AWDFLASH.EXE or download from our web site. STEP 3. Copy latest BIOS for V6FP/V6FU from our web site to your boot disc. STEP 4. Insert your boot disc into A:, start the computer, type “Awdflash A:\V6FPAxxx.BIN /SN/PY/CC/R”...