Table of Contents
Advertisement
Quick Links
V4MDM/V4MDMP/V2MDMP
USER'S MANUAL
M/B For Socket-A Athlon/Duron Processor
NO. G03-V4MDMPR3A
Release date: March 2004
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Advertisement
Table of Contents
Related Manuals for JETWAY V4MDMPR3A
Summary of Contents for JETWAY V4MDMPR3A
- Page 1 V4MDM/V4MDMP/V2MDMP USER'S MANUAL M/B For Socket-A Athlon/Duron Processor NO. G03-V4MDMPR3A Release date: March 2004 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
-
Page 2: Table Of Contents
TABLE OF CONTENT USER’S NOTICE........................ii MANUAL REVISION INFORMATION ................ii COOLING SOLUTIONS ......................ii CHAPTER 1 INTRODUCTION OF V4MDM/V4MDMP/V2MDMP MOTHERBOARD 1-1 FEATURE OF MOTHERBOARD................1 1-2 SPECIFICATION .....................2 1-3 PERFORMANCE LIST ...................3 1-4 LAYOUT DIAGRAM & JUMPER SETTING ............4 CHAPTER 2 HARDWARE INSTALLATION 2-1 HARDWARE INSTALLATION STEPS ..............6 2-2 CHECKING MOTHERBOARD'S JUMPER SETTING........6 2-3 INSTALL CPU ......................8... -
Page 3: User's Notice
USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. -
Page 4: Feature Of Motherboard
Chapter 1 Introduction of V4MDM/V4MDMP Motherboard 1-1 Feature of motherboard The V4MDM/V4MDMP/V2MDMP motherboard is design for use AMD Athlon/ Duron/Athlon XP 200MHz/266MHz/333MHz (Double Data Rate) Front Side Bus Frequency CPU, which utilize the Socket-A design and the memory size expandable to 2.0GB. -
Page 5: Specification
1-2 Specification Spec Description ∗ Micro ATX form factor 4 layers PCB size: 24.4x22.0cm Design ∗ VIA KM400 Memory Graphic Host Chipset (V4MDM/V4MDM) Chipset ∗ VIA KM266Pro Memory Graphic Host Chipset (for V2MDMP) ∗ VIA VT8235 South Bridge ∗ Support 200/266/333MHz (100/133/166MHz) Front Side Bus Clock Generator Clock (CPU Bus clock) ∗... -
Page 6: Performance List
1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report CPU:... -
Page 7: Layout Diagram & Jumper Setting
1-4 Layout Diagram & Jumper Setting V4MDM not support PRINT GAME/MIDI PORT PS/2 Mouse PS/2 Keyboard COM1 LINE-IN LINE-OUT CPU Socket K/B Power ON Jumper (JP1) CPU FAN PS2 KB/Mouse Port USB Port/ ATX Power Connector LAN Connector (V4MDM not support) CPU Ratio Jumper (JP4) FAN2 PC99 Back Panel... -
Page 8: Expansion Sockets
Jumpers Jumper Name Description Page CPU Ratio Selector 2x5-pin Block JP7, JP8 CPU Front Side Bus Frequency 2-pin Block JBAT CMOS RAM Clear 3-pin Block Keyboard Power On Enable/Disabled 3-pin Block Connectors Connector Name Description Page ATXPOW ATX Power Connector 20-pin Block P.12 KB/MS... -
Page 9: Chapter 2 Hardware Installation
Chapter 2 Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard setting 2. Install CPU 3. Install Memory 4. Install Expansion cards 5. Connect Ribbon cables, Panel wires, and power supply 6. -
Page 10: Troubleshooting
(2) CPU Front Side Bus Frequency Setting (2-pin) : JP7, JP8 CPU CLK 100MHz 133MHz (Default) 166MHz 100MHz 133MHz 166MHz (Default) CPU Front Side Bus Frequency Setting Note: CPU Front Side Bus Frequency also can setting step by step in BIOS SETUP, please refer page Miscellaneous Control in Host Clock at Next. -
Page 11: Install Cpu
(4) Keyboard Power On function Enabled/Disabled (3-pin): JP1 When setting Enabled you can using keyboard by key in password to power on system. 1-2 closed K/B Power ON Disable 2-3 closed K/B Power ON Enabled (Default) Keyboard Power On Setting 2-3 Install CPU 2-3-1 Glossary Chipset (or core logic) - two or more integrated circuits which control the interfaces between... -
Page 12: About Amd Athlon & Duron 462-Pin Cpu
Front Side Bus Frequency - the working frequency of the motherboard, which is generated by the clock generator for CPU, DRAM and PCI BUS. CPU L2 Cache - the flash memory inside the CPU, normally Athlon CPU has 256K or above, while Duron will have 64K. -
Page 13: Install Memory
2-4 Install Memory This motherboard provides 184-pin DUAL INLINE MEMORY MODULES (DIMM) sites for memory expansion available from minimum memory size of 64MB to maximum memory size of 2.0GB DDR SDRAM. Valid Memory Configurations Bank 184-Pin DIMM Total Memory Bank 0, 1 (DDR1) DDR200/DDR266/DDR333 64MB∼1.0GB DDR SDRAM Module... -
Page 14: Expansion Card
2-5 Expansion Cards WARNING! Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2-5-1 Procedure For Expansion Card Installation 1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers. -
Page 15: Interrupt Request Table For This Motherboard
Interrupt request are shared as shown the table below: INT A INT B INT C INT D PCI slot 1 Shared PCI slot 2 Shared PCI slot 3 Shared ... - Page 16 ROW2 ROW1 3.3V 3.3V -12V 3.3V Soft Power On Power OK +5V (for Soft Logic) +12V Pin 1 PS/2 Mouse & PS/2 Keyboard Connector: KB/MS The connectors for PS/2 keyboard and PS/2 Mouse. USB Port connector: USB The connectors are 4-pin connector that connect USB devices to the system board. LAN Port connector: LAN (V4MDM not support) This connector is standard RJ45 connector for Network.
- Page 17 Pin 1 Floppy Drive Connector (10) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly.
-
Page 18: Headers
2-6-2 Headers Line-Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-out, MIC connector with cable. AUDIO Pin 1 AUD _ MIC AUD _ G ND AUD _ VCC AUD _ MIC _ BIAS AUD _ R ET _ R AUD _ FPO UT _ R HP _ O N AUD _ RET _ L... - Page 19 Speaker connector: SPEAK This 4-pin connector connects to the case-mounted speaker. See the figure below. Power LED: PWR LED The Power LED is light on while the system power is on. Connect the Power LED from the system case to this pin. Power switch: PWR BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system.
- Page 20 CPUFAN FAN2 FAN1 (11) IR infrared module Headers (5-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. Pin 1 IR infrared module Headers (12) CD Audio-In Headers (4-pin) : CDIN CDIN is the connector for CD-Audio Input signal.
-
Page 21: Starting Up Your Computer
2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used. -
Page 22: Chapter 3 Introducing Bios
Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. -
Page 23: The Main Menu
3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. -
Page 24: Standard Cmos Features
Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performances system operations. Load Standard Defaults Use this menu to load the BIOS default values for the minimal/stable performance system operation. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. -
Page 25: Advanced Bios Features
Time The time format is <hour><minute><second>. Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. - Page 26 Anti-Virus Protection Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
-
Page 27: Advanced Chipset Features
Typematic Rate Setting Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled. Typematic Rate (Chars/Sec) Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30. -
Page 28: Dram Timing Settings
DRAM Timing Settings Please refer to section 3-6-1 AGP Timing Settings Please refer to section 3-6-2 PCI Timing Settings Please refer to section 3-6-3 System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. -
Page 29: Agp Function Setting
RAS Precharge Time If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. -
Page 30: Integrated Peripherals
3-7 Integrated Peripherals CMOS Setup Utility – Copyright(C) 1984-2004 Award Software Integrated Peripherals > OnChip IDE Function Press Enter Item Help > OnChip Device Function Press Enter > Onboard Super IO Function Press Enter Init Display First PCI Slot Menu Level > ↑↓→←... -
Page 31: Onchip Device Function
OnChip IDE Channal0/Channel1 The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. -
Page 32: Onboard Super Io Function
AC97 Modem Device This item allows you to decide to enable/disable the chipset family to support AC97 Modem. The settings are: Auto, Disabled. USB Host Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripherals. -
Page 33: Power Management Setup
Parallel Port Mode : Standard Parallel Port : Enhanced Parallel Port : Extended Capability Port SPP/EPP/ECP/ECP+EPP To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the onboard parallel port will operate in ECP mode only. -
Page 34: Wake Up Events
Modem Use IRQ This determines the IRQ in which the MODEM can use. The settings are: 3, 4, 5, 7, 9, 10, 11, NA. Power Button Function Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state. The settings are: Delay 4 Sec, Instant-Off. -
Page 35: 3-8-1.1 Irqs Activities
3-8-1.1 IRQs Activities CMOS Setup Utility – Copyright(C) 1984-2004 Award Software IRQs Activities Primary INTR Item Help IRQ3 (COM 2) Enabled IRQ4 (COM 1) Enabled IRQ5 (LPT 2) Enabled Menu Level >>> IRQ6 (Floppy Disk) Enabled IRQ7 (LPT 1) Enabled IRQ8 (RTC Alarm) Disabled... -
Page 36: Irq Resources
The settings are: Auto(ESCD), Manual. IRQ Resources When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. Please refer to section 3-9-1 PCI/VGA Palette Snoop Leave this field at Disabled. The settings are Enabled, Disabled. 3-9-1 IRQ Resources CMOS Setup Utility –... -
Page 37: Miscellaneous Control
Shutdown Temperature This item can let users setting the Shutdown temperature, when CPU temperature over this setting the system will auto shutdown to protect CPU. Show PC Health in Post During Enabled, it displays information list below. The choice is either Enabled or Disabled Current CPU Temperature/Current System Temp/Current FAN1, FAN2 Speed/Vcore/ Vdd/3.3V/+5V/+12V/-12V/VBAT(V)/5VSB(V) This will show the CPU/FAN/System voltage chart and FAN Speed. -
Page 38: Load Standard/Optimized Defaults
3-12 Load Standard/Optimized Defaults Load Standard Defaults When you press <Enter> on this item, you get confirmation dialog box with a message similar Load Standard Defaults (Y/N)? N Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system operations. -
Page 39: Chapter 4 Driver & Free Program Installation
Chapter 4 DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. -
Page 40: Via 4 In
4-1 VIA 4 IN 1 Install VIA Service Pack 4 IN 1 Driver * The path of the file is X:\VIA\DRIVER\SETUP.EXE IDE : VIA ATAPI VENDOR SUPPORT DRIVER IS USED TO FIXED COMPATIBILITY ISSUE FOR IDE DEVICES AGPVXD : VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART.VXD WILL PROVIDE SERVICE ROUTINES TO YOUR VGA DRIVER AND INTERFACE DIRECTLY TO HARDWARE, PROVIDING FAST GRAPHIC ACCESS... -
Page 41: Vga
7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer 4-2 VGA install VIA VGA Driver For WINDOWS 9X/ME/NT4.0/2000/XP 1. Click VGA when MAGIC INSTALL MENU Click NEXT When VIA/S3G KM400 appears Display driver setup Appears... -
Page 42: Sound
4-3 SOUND install ALC AC97’ Codec Audio Driver 1. Click SOUND when MAGIC INSTALL 2. Then auto detect operation system language MENU appears edition, click NEXT, start to install DRIVER 3. Click Finish and Restart Windows 4. Click Start→Program→Avance Sound Manager→AvRack. - Page 43 4-3-1 SOUND install VIA AC97’ Codec Audio Driver 1. Click SOUND when MAGIC INSTALL 2. Then auto detect operation system language MENU appears edition, click NEXT, start to install DRIVER 3. Click NEXT 4. Click Continue Anyway 5 . Click Finish and Restart Windows 6.
-
Page 44: Lan Install Via 10/100Mb Lan Controller Driver
4-4 LAN Install VIA 10/100MB LAN Controller Driver (V4MDM not support) The VIA 10/100MB PCI Ethernet Adapter Driver path is X:\VIA\LANDRV 1. Click LAN when Magic Install Menu appear 2. Click Yes and restart your computer 4-5 PC-HEALTH ITE Smart Guardian Software The path of the file is X:\VIA\ITESMARTGD\SETUP.EXE (Support Windows 9X/ME/2K/NT/XP) 1. -
Page 45: Mbios&Dx9 Install Bios Live Update Utility
4-6 MBIOS&DX9 Install BIOS Live Update Utility Click Magic BIOS when Magic Install Click Next to install the Magic BIOS in MENU appears Destination Folder After finish Setup you will have a Magic Double click the Magic BIOS icon you will BIOS icon in your screen have this picture, choose from internet you can upgrade BIOS On-line... -
Page 46: Usb2.0
When choose From Local Driver to update 10. Choose the correct BIOS file to update BIOS BIOS, you must have the correct BIOS file in your Local Driver 4-7 USB2.0 Install VIA USB2.0 Device Driver The Windows XP OS need service Pack 1 support 1. -
Page 47: Pc-Cillin
4-8 PC-CILLIN Install PC-CILLIN 2004 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2. Click NEXT when the "Trend Micro internet MENU appear security" installshield wizard windows appear 3. This is license agreement, select "I Accept 4. Click NEXT and Enter your Customer the terms"... -
Page 48: How To Disable On-Board Sound
7. After PC-CILLIN 2004 complete, Please register your information and we recommend select update item to download newest engine code and virus code Note : Please install ACROBAT READER, Before you read PC-CILLIN 2004 User Manual, the path at X:\acrobat\adberdr6_enu_full.exe 4-9 HOW TO DISABLE ON-BOARD SOUND Enter BIOS SETUP choose INTEGRATE PERIPHERALS choose ON-CHIP DEVICE FUNCTION choose AC97 SOUND DEVICE...