1. Manuals
  2. Brands
  3. JETWAY Manuals
  4. Motherboard
  5. V6DP
  6. User manual

JETWAY V6DP User Manual

M/b for socket-a athlon/duron processor
Hide thumbs
Table of Contents

Advertisement

Quick Links

V6DP/V6DU
USER'S MANUAL
M/B For Socket-A Athlon/Duron Processor
NO. G03-V6DPR4A
Release date: September 2003
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject
to change at any time without notice, and should not be construed as a commitment by manufacturer.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V6DP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for JETWAY V6DP

Summary of Contents for JETWAY V6DP

  • Page 1 V6DP/V6DU USER'S MANUAL M/B For Socket-A Athlon/Duron Processor NO. G03-V6DPR4A Release date: September 2003 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

  • Page 2: Table Of Contents

    TABLE OF CONTENT USER’S NOTICE ......................ii MANUAL REVIS1ION INFORMATION ................ii COOLING SOLUTIONS ....................ii CHAPTER 1 INTRODUCTION OF V6DP/V6DU MOTHERBOARD 1-1 FEATURE OF MOTHERBOARD................1 1-2 SPECIFICATION .....................2 1-3 PERFORMANCE LIST ...................3 1-4 LAYOUT DIAGRAM & JUMPER SETTING ............4 CHAPTER 2 HARDWARE INSTALLATION 2-1 HARDWARE INSTALLATION STEPS ..............6...

  • Page 3: User's Notice

    TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE V6DP/V6DU MOTHER-BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE.

  • Page 4: Chapter 1 Introduction Of V6Dp/V6Du Motherboard

    A series CPUs based system, by integrating a high performance North Bridge, advanced hardware 2D/3D GUI engine and Super-South Bridge. The V6DP/V6DU provided 2 pcs DDR Module Socket support DDR 200/266 SDRAM. Moreover, by integrating the Ultra AGP technology and advanced 128-bit graphic display interface and provides powerful hardware decoding DVD accelerator to improve the DVD playback performance.

  • Page 5: Specification

    133 MB/s ∗ VIA VT6103 LAN PHY support 10/100Mbps full duplex, half On board LAN duplex operation (for V6DP) ∗ Support Boot On LAN function ∗ AC’97 Digital Audio controller integrated Audio ∗ AC’97 Audio CODEC on board ∗...

  • Page 6: Performance List

    1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report CPU:...

  • Page 7: Layout Diagram & Jumper Setting

    1-4 Layout Diagram & Jumper Setting (for V6DP) PRINT GAME/MIDI PORT PS/2 Mouse PS/2 Keyboard COM1 LINE-IN LINE-OUT K/B Power ON CPU Socket Jumper (JP1) CPU FAN PS2 KB/Mouse Port ATX Power USB Port/ Connector LAN Connector FAN2 PC99 Back Panel...

  • Page 8: Expansion Sockets

    PS/2 Mouse & PS/2 Keyboard 6-pin Female P.12 Connector USB Port Connector 4-pin Connector P.12 RJ-45 LAN Port Connector RJ-45 Connector P.12 (for V6DP) PARALL Parallel Port Connector 25-pin Female P.12 AUD _ GAME Audio/Game Connector 3 phone jack + 15-pin Connector P.12 COM1...

  • Page 9: Hardware Installation Steps

    Chapter 2 Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard setting 2. Install CPU 3. Install Memory 4. Install Expansion cards 5. Connect Ribbon cables, Panel wires, and power supply 6.

  • Page 10: Install Cpu

    (3) CMOS RAM Clear (3-pin) : JBAT A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2 pins of JBAT to store the CMOS data. To clear the CMOS, follow the procedure below: Turn off the system and unplug the AC power Remove ATX power cable from ATX power connector Locate JBAT and short pins 2-3 for a few seconds Return JBAT to its normal setting by shorting pins 1-2...

  • Page 11: About Amd Athlon & Duron 462-Pin Cpu

    PCI - Peripheral Component Interconnect - a high speed interface for video cards, sound cards, network interface cards, and modems; runs at 33MHz. ISA - Industry Standard Architecture - a relatively low speed interface primarily used for sound cards and modems; runs at approx. 8MHz. Serial Port - a low speed interface typically used for mouse and external modems.

  • Page 12: Install Memory

    To install a CPU, first turn off your system and remove its cover. Locate the ZIF socket and open it by first pulling the level sideways away from the socket then upward to a 90-degree angle. Insert the CPU with the correct orientation as shown below. The notched corner should point toward the end of the level.

  • Page 13: Expansion Card

    NOTE! When you install DIMM module fully into the DIMM socket the eject tab should be locked into the DIMM module very firmly and fit into its indention on both sides. WARNING! For the DDR SDRAM CLOCK is set at 133MHz, use only DDR266-compliant DDR Modules.

  • Page 14: Interrupt Request Table For This Motherboard

    Interrupt request are shared as shown the table below: INT A INT B INT C INT D    PCI slot 1 Shared    PCI slot 2 Shared    PCI slot 3 Shared   ...
  • Page 15 The connectors for PS/2 keyboard and PS/2 Mouse. USB Port connector: USB The connectors are 4-pin connector that connect USB devices to the system board. LAN Port connector: LAN (only for V6DP) This connector is standard RJ45 connector for Network. Parallel Port Connector (25-pin female): PARALL Parallel Port connector is a 25-pin D-Subminiature Receptacle connector.
  • Page 16 Pin 1 Floppy Drive Connector (10) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly.

  • Page 17: Headers

    2-6-2 Headers (1) Line-In/Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-In, Line-out, MIC connector with cable. AUDIO Pin 1 AUD _ MIC AUD _ G ND AUD _ VCC AUD _ MIC _ BIAS AUD _ R ET _ R AUD _ FPO UT _ R HP _ O N AUD _ RET _ L...
  • Page 18 Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system’s power supply. See the figure below.
  • Page 19 (11) FAN Headers (3-pin) : FAN1, FAN2, CPUFAN These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan’s plug to the board taking into consideration the polarity of connector.

  • Page 20: Starting Up Your Computer

    1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used.

  • Page 21: Entering Setup

    Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization.

  • Page 22: The Main Menu

    Once you enter Award  BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.

  • Page 23: Standard Cmos Features

    Use this menu to load the BIOS default values that are factory settings for optimal performances system operations. Load Standard Defaults Use this menu to load the BIOS default values for the minimal/stable performance system operation. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. Save &...

  • Page 24: Advanced Bios Features

    Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use Manual to define your own drive type manually.
  • Page 25 Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.

  • Page 26: Advanced Chipset Features

    Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled. Typematic Rate (Chars/Sec) Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30.

  • Page 27: Dram Timing Settings

    Please refer to section 3-6-1 AGP Timing Settings Please refer to section 3-6-2 PCI Timing Settings Please refer to section 3-6-3 System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result.

  • Page 28: Agp Function Setting

    If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system.

  • Page 29: Integrated Peripherals

    3-7 Integrated Peripherals CMOS Setup Utility – Copyright(C) 1984-2003 Award Software Integrated Peripherals > OnChip IDE Function Press Enter Item Help > OnChip Device Function Press Enter > Onboard Super IO Function Press Enter Init Display First PCI Slot Menu Level > ↑↓→←...

  • Page 30: Onchip Device Function

    OnChip IDE Channal0/Channel1 The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports.

  • Page 31: Onboard Super Io Function

    AC97 Modem Device This item allows you to decide to enable/disable the chipset family to support AC97 Modem. The settings are: Auto, Disabled. USB Host Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripherals.

  • Page 32: Power Management Setup

    Parallel Port Mode : Standard Parallel Port : Enhanced Parallel Port : Extended Capability Port SPP/EPP/ECP/ECP+EPP To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the onboard parallel port will operate in ECP mode only.

  • Page 33: Wake Up Events

    Modem Use IRQ This determines the IRQ in which the MODEM can use. The settings are: 3, 4, 5, 7, 9, 10, 11, NA. Power Button Function Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state. The settings are: Delay 4 Sec, Instant-Off.

  • Page 34: 3-8-1.1 Irqs Activities

    3-8-1.1 IRQs Activities CMOS Setup Utility – Copyright(C) 1984-2003 Award Software IRQs Activities Primary INTR Item Help IRQ3 (COM 2) Enabled IRQ4 (COM 1) Enabled IRQ5 (LPT 2) Enabled Menu Level >>> IRQ6 (Floppy Disk) Enabled IRQ7 (LPT 1) Enabled IRQ8 (RTC Alarm) Disabled...

  • Page 35: Irq Resources

    by a “>”). The settings are: Auto(ESCD), Manual. IRQ Resources When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. Please refer to section 3-9-1 PCI/VGA Palette Snoop Leave this field at Disabled. The settings are Enabled, Disabled. 3-9-1 IRQ Resources CMOS Setup Utility –...

  • Page 36: Miscellaneous Control

    This item can let users setting the Shutdown temperature, when CPU temperature over this setting the system will auto shutdown to protect CPU. Show PC Health in Post During Enabled, it displays information list below. The choice is either Enabled or Disabled Current CPU Temperature/Current System Temp/Current FAN1, FAN2 Speed/Vcore/ Vdd/3.3V/+5V/+12V/-12V/VBAT(V)/5VSB(V) This will show the CPU/FAN/System voltage chart and FAN Speed.

  • Page 37: Load Standard/Optimized Defaults

    Load Standard Defaults When you press <Enter> on this item, you get confirmation dialog box with a message similar Load Standard Defaults (Y/N)? N Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system operations. Load Optimized Defaults When you press <Enter>...

  • Page 38: Magic Install Supports Windows 95/98/98Se/Nt4.0/2000/Xp

    VIA Service Pack 4 IN 1 driver install VIA VGA driver SOUND install ALC or CMI Audio Codec driver install VIA 10/100MB LAN Controller driver (Only for V6DP) USB2.0 install USB 2.0 driver DIRECTX8 install Microsoft DirectX 8.1 driver...

  • Page 39: Via 4 In 1 Install Via Service Pack 4 In 1 Driver

    AGPVXD : VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART.VXD WILL PROVIDE SERVICE ROUTINES TO YOUR VGA DRIVER AND INTERFACE DIRECTLY TO HARDWARE, PROVIDING FAST GRAPHIC ACCESS IRQ ROUTING : VIA PCI IRQ MINIPORT DRIVER IS TO BE INSTALLED UNDER WIN98 ONLY, IT WILL FIX PCI IRQ ROUTING SEQUENCE INF : VIA REGISTRY DRIVER IS TO BE INSTALLED UNDER WINDOWS...

  • Page 40: Vga

    7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer 4-2 VGA install VIA VGA Driver For WINDOWS 9X/ME/NT4.0/2000/XP 1. Click VGA when MAGIC INSTALL MENU 2.

  • Page 41: Sound

    4-3 SOUND install ALC or CMI AC97’ Codec Audio Driver 4-3-1 Install ALC AC97’ Codec Audio Driver 1. Click SOUND when MAGIC INSTALL 2. Then auto detect operation system language MENU appears edition, click OK, start to install DRIVER 3. Click Finish and Restart Windows 4.

  • Page 42: Install Cmi Audio Codec Driver

    4-3-2 Install CMI Audio Codec Driver 1. Click SOUND when MAGIC INSTALL 2. Choose Install component in Installation MENU appears Package 3. Click Next when copyright Issue appears, click 4. Enter Program folders name or click Next Next or choose BROWSE to change the path for the file to be store 5.

  • Page 43: Lan

    2-channel speaker plug in Line-In as Front Speaker to get 4-channel effect 4-4 LAN Install VIA 10/100MB LAN Controller Drive r (for V6DP) The VIA 10/100MB PCI Ethernet Adapter Driver path is X:\VIA\LANDRV Click LAN when Magic Install Menu appear 2.

  • Page 44: Magic Bios Install Bios Live Update Utility

    1. Click PC-Health when Magic Install Menu 2. Click OK when Winbond Hardware Doctor appears Setup Window appears 3. Click the Button to start installation 4. Select Program Group name or enter a new group name, click continue to setup and click OK after setup complete 4-5-1 How To Utilize PC-HEALTH 1.
  • Page 45 After finish Setup you will have a Magic Double click the Magic BIOS icon you will BIOS icon in your screen have this picture, choose from internet you can upgrade BIOS On-line When On-line update BIOS the program Click Next if you need update BIOS, after will auto-check your BIOS version upgrade BIOS, the system will clear CMOS and automatically restart...

  • Page 46: Usb2.0

    4-7 USB2.0 Install VIA USB2.0 Device Driver 1. Click USB2.0 when MAGIC INSTALL 2. When USB2.0 Setup Program Appear, Click MENU Appear NEXT 3. Select Install USB Driver and Click NEXT Select FINISH and Restart your Computer 5. Check device working properly in Device Manager The Path of the file is X:\VIA\VIAUSB20\SETUP.EXE...

  • Page 47: Pc-Cillin

    4-8 PC-CILLIN Install PC-CILLIN 2002 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2. (1) Click "Install PC-CILLIN" when PC- MENU appear CILLIN 2002 main menu appears, and Click NEXT when "Install Shield Wizard For PC- CILLIN 2002" (2) Click Open Manual. you can learn PC- CILLIN 2002 how to use 3.

  • Page 48: How To Disable On-Board Sound

    You may copy from DRIVER CD X:\FLASH\AWDFLASH.EXE or download from our web site. STEP 3. Copy latest BIOS for V6DP/V6DU from our web site to your boot disc. STEP 4. Insert your boot disc into A:, start the computer, type “Awdflash A:\V6DPAxxx.BIN /SN/PY/CC/R”...

This manual is also suitable for:

V6du

Table of Contents