Related Manuals for Ultra Start 1500 SERIES
Summary of Contents for Ultra Start 1500 SERIES
- Page 1 1500 1500 INSTALLATION GUIDE 1500M Advanced Remote Vehicle Starter 1500 Automatic and Manual Trans WWW.ULTRASTARTERS.COM TECH SUPPORT N Version...
- Page 2 TABLE OF CONTENTS 1500 Wiring Diagram Page 3 Pre-Installation Page 4 Wire Connectors Page 5 Installation Page 6-7 Programming Page 7-9 System Reset Operations Page 10 Additional Operations Page 11 Emergency System Service Mode Relay Diagrams Page 12 DIAGNOSTICS DIAGNOSTICS DIAGNOSTICS PARK LIGHTS PARK LIGHTS...
-
Page 3: Wiring Diagram
WIRING DIAGRAM (+) 30amp Output Starter Yellow Heater (+) 30amp Output Green (+) 30amp Input Main Power Main Power (+) 30amp Input White Selectable (+) 30amp Output Ignition 1 Blue (+) 30amp Output (-)500ma Output RE-ARM Yellow (-)500ma Output ANTI-THEFT BYPASS Orange (-)500ma Output FACTORY DISARM... -
Page 4: Installation Tips
INSTALLATION TIPS Components Recommended Pre-Installation Procedures BEFORE STARTING INSTALLATION Note: This remote starter is designed for fuel injected and diesel engines Recommended Installation Procedures Proper Connections - Under Hood Connections - BE CAREFUL Installing the External Long Range Antenna - BLUE NOTE Mounting The Control Module - Never... - Page 5 WIRING CONNECTORS 6 Pin Power Connector Yellow Starter 12volts during crank only. Green Heater 12volts in accessory off during start. 12 power Constant 12volt power at ignition harness. 12 power Constant 12volt power at ignition harness. Blue Ignition 1 12volts in ignition and start positions. White Selectable Selectable Output.
- Page 6 QUICK START INSTALL Step 1 - Connect All Of the Following Wires 6 Pin Power Connector Yellow Starter Output Green Heater Output 12 power Input - High Current. 12 power Input - High Current. Blue Ignition 1 Output White Selectable See page 5 14 Pin Power Connector Black...
- Page 7 PROGRAMMING Programming Overview User Settings - Page 8 Starter Settings - Page 9 Tach Settings - Page 8 Entering Program Mode To Enter Program Mode Leave in the “ON” position. Press Button #1 Lock User Options Page 8 Press Button #3 Start Remote Start Options Page 9...
- Page 8 PROGRAMMING PROGRAM MODE - TACH SETTINGS See page 6 for Auto Tach Learning Setting 1- Method 2- Low Idle Learn (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time. Press the # button on the remote.(Button #4). Using the ignition key, make sure not to turn the key off at any time or your will exit programming.
- Page 9 PROGRAMMING PROGRAM MODE - STARTER SETTINGS Enter STARTER Program Mode - See Page 7 for details on entering program mode Setting 1- Special Door Lock/ Unlock Operations Chrysler / VW Re-Arm 1 Flash Unlock pulse before start and a lock pulse after start GM Auto Re-Lock 2 Flashes Lock pulse after remote starter shuts off...
- Page 10 OPERATIONS See Owner’s Guide for More Detail on Operations 2 Times if programmed for safety start 2nd Car Operation & & 2 Times if programmed for safety start & & then Cold Start Mode TO CANCEL COLD START MODE Note: Starting the vehicle with the key or remote starting the vehicle will cancel Cold Start Mode. Reservation Mode - Manual Trans.
-
Page 11: Other Features
OTHER FEATURES Transmitter Programming Step 1 Leaving Key ON Step 2 Step 3 Step 4 LOCK 1st car Note: All the transmitters All transmitters not programmed at this time will be erased from memory for security. The system holds a maximum of 3 transmitter codes including 2nd car remote codes. - Page 12 RELAY DIAGRAMS Negative Type Door Locks Positive Type Door Locks 5 Wire / Reverse Polarity Type Door Locks Vacuum Type Door Locks DIAGNOSTICS...