MULTIQUIP FS2 Parts And Operation Manual
  1. Manuals
  2. Brands
  3. MULTIQUIP Manuals
  4. Saw
  5. FS2
  6. Parts and operation manual
MULTIQUIP FS2 Parts And Operation Manual

MULTIQUIP FS2 Parts And Operation Manual

Concrete saw
Hide thumbs Also See for FS2:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operation and Parts Manual
PARTS AND OPERATION MANUAL

CONCRETE SAW

MODEL FS2
MODEL #
SERIAL #
Revision #2 (11/08/01)
MULTIQUIP INC. . . . .
18910 WILMINGTON AVE.
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700
800-421-1244
FAX: 310-537-3927
E-mail:mq@multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Montreal, Canada • Manchester, UK
Rio De Janiero, Brazil • Guadalajara, Mexico
PARTS DEPARTMENT:
800-427-1244
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
800-478-1244
FAX: 310-631-5032
•
www:multiquip.com
P/N 15700

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FS2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for MULTIQUIP FS2

Summary of Contents for MULTIQUIP FS2

  • Page 1: Concrete Saw

    PARTS AND OPERATION MANUAL CONCRETE SAW MODEL FS2 MODEL # SERIAL # Revision #2 (11/08/01) MULTIQUIP INC..PARTS DEPARTMENT: 18910 WILMINGTON AVE. 800-427-1244 CARSON, CALIFORNIA 90746 FAX: 800-672-7877 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE: 310-537-3700 800-421-1244 800-478-1244 FAX: 310-537-3927 FAX: 310-631-5032 •...

  • Page 3: Here's How To Get Help

    FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 3...

  • Page 4: Table Of Contents

    Blade Shaft Assembly ........38-39 Engine Mount Assembly ........40-41 Pointers and Covers Assembly ......42-43 NOTE Specification and part number are subject to change without notice PAGE 4 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 5: Parts Ordering Procedures

    10+ line items. Toll-free FAX: 800/6-PARTS-7 • 800-672-7877 *DISCOUNTS ARE SUBJECT TO CHANGE* Fax order discount and UPS special programs revised June 1, 1995 MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 5...

  • Page 6: Safety Message Alert Symbols

    Potential hazards associated with Concrete Saw operations injury. will be referenced with Hazard Symbols which appear throughout this manual, and will be referenced in conjunction with Safety Message Alert Symbols. PAGE 6 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 7: Safety Message Alert Symbols

    OSHA or other applicable local regulations. NOTE This concrete saw, other property, or the surrounding environment could be damaged if you do not follow instructions. MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 7...

  • Page 8: Decals

    Machine Safety Decals The FS2 Concrete Saw is equipped with a number of safety decals (Figure 1). These decals are provided for operator safety and maintenance information. The illustration shows these decals as they appear on the concrete saw. Should any of these decals become unreadable, replacements can be obtained from you dealer.

  • Page 9: Rules For Safe Operation

    Whenever necessary, replace nameplate, operation and safety decals when they become difficult to read. Always check the machine for loosened threads or bolts before starting. MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 9...
  • Page 10 Test the ON/OFF switch before operating. The purpose of the NEVER transport the saw with the blade mounted. switch is to shut down the engine. PAGE 10 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 11: Rules For Safe Operation

    Dispose of hazardous waste properly. Examples of potentially hazardous waste are used motor oil, fuel and fuel filters. DO NOT use food or plastic containers to dispose of hazardous waste. MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 11...

  • Page 12: Dimensions

    ( " l e e ( " l e e ( " ( " t a r ( " " 0 " 4 PAGE 12 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 13: Weights

    , " 4 , " 4 , " 4 , " 4 , " 4 , " 4 t a r ) . s MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 13...

  • Page 14: Basic Components

    FS2 CONCRETE SAW — BASIC COMPONENTS BASIC COMPONENTS Figure 4. FS2 Concrete Saw Basic Components PAGE 14 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)
  • Page 15 14-INCH BLADE GUARD ASSEMBLY SEE PAGE 48 18-INCH BLADE GUARD ASSEMBLY SEE PAGE 50 RAISE/LOWER ASSEMBLY SEE PAGE 52 GASOLINE ENGINE ASSEMBLIES SEE PAGE 54 MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 15...

  • Page 16: Basic Engine Components

    10. Fuel Tank – Holds unleaded gasoline. For additional information refer to engine owner's manual. PAGE 16 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 17: General Information

    ) 1 . o l c r i A r t l i i t a ) 8 . MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 17...
  • Page 18 The blade guard may be oriented for left or right hand cutting. See pages 48 and 50. " 6 " 8 " 8 " 8 PAGE 18 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 19: General Information

    Engine ON/OFF Switch – Pull this switch to permit the engine to be started by pull rope. Push the switch inward to stop the engine. Figure 6. FS2 Concrete Saw Console MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 19...

  • Page 20: Inspection Engine

    3. When refueling, be sure to use a strainer for filtration. DO Reference manufacturer engine manual for NOT top-off fuel. Wipe up any spilled fuel. specific servicing instructions. PAGE 20 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 21: Inspection Blade

    “under cutting” condition brought about by highly abrasive material or improper under cutting core protection. MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 21...
  • Page 22 The inside surface of the flange must be free of debris and permit a tight closure on the surface of the blade core. Figure 10. Diamond Blade Placement PAGE 22 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 23: Inspection-Guards, Covers, And V-Belts

    This flange cover is to be in place when cutting from either the right or left side of the saw. Figure 12. Blade Flange Cover Figure 14. V-Belt Parallelism MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 23...

  • Page 24: Inspection-Guards, Covers, And V-Belts

    (loose on pulleys). 5. If the V-belts becomes worn or loose, replace them by using V-belt part number 15082. PAGE 24 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 25: Initial Start-Up

    Figure 17. Engine ON/Off Switch 5. PULL the Console Engine ON/OFF switch (Figure 18) to the "PULL-ON" position. Figure 20. Throttle Lever Figure 18. Console Engine ON/Off Switch MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 25...

  • Page 26: Initial Start-Up

    11. All sawing is done at full throttle. Your engine governor has been set at the factory to ensure an optimum speed setting. PAGE 26 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 27: Operation

    Raise/Lower handle clockwise: while observing the depth of the cut desired by referencing the depth feed gauge (Figure 6). IF the water supply to your blade is interrupted, stop sawing immediately. MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 27...

  • Page 28: Operation

    PAGE 28 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 29: Maintenance

    Ensure that the disposition of all hazardous plished AFTER steam cleaning operations. waste is handled properly. Call your Recycling Center for information about recycling engine oil. MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 29...
  • Page 30 7. To complete the re-installation process , reverse the order of the above mentioned steps. For V-belt adjustment, see V-belt tension section on page 23 (Figure 14). Figure 25. Right-Side Shaft Bearing PAGE 30 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 31: Maintenance

    2. Tighten the (2) hex head cap screws, item 12, page 40. that provide optimum torque transfer. 3. Replace the belt cover, item 4, page 42. MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 31...

  • Page 32: Explanation Of Codes In Remarks Column

    Note: If more than one of the same reference number is listed, the last one listed indicates newest (or latest) part available. NOTE The contents of this parts catalog are subject to change without notice. PAGE 32 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 33: Suggested Spare Parts

    2 .... 15091 ....WHEELS, REAR 2 .... 15090 ....WHEELS, FRONT 1 .... 15097 ....WRENCH, ALL PURPOSE 1 .... 15098 ....TOOL, SHAFT LOCK MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 33...

  • Page 34: Troubleshooting (Engine)

    . r o l i f r e t t l i f . r e r i A n i l n i l PAGE 34 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

  • Page 35: Troubleshooting (Engine)

    MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 35...
  • Page 36 FS2 CONCRETE SAW — UNDER CARRIAGE ASSY. UNDER CARRIAGE ASSY. PAGE 36 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)
  • Page 37 WASHER, FLAT 3/4 SAE SET SCREW 15091 WHEEL, R 9.75 OD X 2.75W X75BB 3615 COLLAR, SET 3/4 SAE ......2 ..... INCLUDES ITEM W/ MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 37...
  • Page 38 FS2 CONCRETE SAW — BLADE SHAFT ASSY. BLADE SHAFT ASSY. PAGE 38 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)
  • Page 39 BELT, V BLADE 3X V335 15061 PULLEY, TL 3V 4.50 0D 15060 BUSHING, TL 1 1/4 BORE 15148 SPACER, BLADE SHAFT 15092 NUT, 1-14-28 MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 39...
  • Page 40 FS2 CONCRETE SAW — ENGINE MOUNT ASSY. ENGINE MOUNT ASSY. PAGE 40 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)
  • Page 41 WASHER, FLAT3/8 SAE 9154 SCREW, HHC 3/8-16 X 1-3/4 1456 NUT, HEX FINISH 3/8-16 15174 BOLT, CARRIAGE 3/8-16 X 3 15564 SCREW, HHC 3/8-16 X 1-3/4 MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 41...
  • Page 42 FS2 CONCRETE SAW — POINTERS AND COVERS ASSY. POINTERS AND COVERS ASSY. PAGE 42 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)
  • Page 43 SCREW, HHC 3/8-16 X 1-1/4 10133 NUT, NYLOC 3/8-16 15088 COVER, BLADE FLANGE 0131A SCREW, HHC 1/4-20 X 3/4 15052 ROD, POINTER 0948 WASHER, FLAT 1/4 SAE MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 43...
  • Page 44 FS2 CONCRETE SAW — WATER SYSTEM ASSY. WATER SYSTEM ASSY. PAGE 44 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)
  • Page 45 FITTING, 1/2 NPT 3/8 BARB 2190 SPACER, 0.25 00 X 0.25L .035W 15544 FITTING,FNPTX 3/4 GARDEN HS BRASS 15546 GASKET,3/4 HOSE GASKET/SCREEN 15173 WASHER, FLAT #8 MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 45...
  • Page 46 FS2 CONCRETE SAW — BASIC PLATFORM ASSY. BASIC PLATFORM ASSY. PAGE 46 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)
  • Page 47 SCREW, HHC 1/4-20 X 3/4 11534 NUT U TYPE 1/4-20 15138 WRENCH, 6” POCKET SOCKET 15098 TOOL, SHAFT LOCK SOCKET 15097 WRENCH, ALL PURPOSE MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 47...
  • Page 48 FS2 CONCRETE SAW — BLADE MIST 14-INCH ASSY. BLADE MIST 14-INCH ASSY. PAGE 48 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)
  • Page 49 GASKET, MANIFOLD MIST 15096 ANGLE, SPLASH GUARD 15043 FLAP, NEOPRINE WATER SHIELD 15005 GUARD, BLADE 14” BODY W/A 26250 SCREW, HHC 1/4-20 X 1-3/4 MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 49...
  • Page 50 FS2 CONCRETE SAW — BLADE MIST 18 -INCH ASSY. BLADE MIST 18-INCH ASSY. PAGE 50 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)
  • Page 51 GASKET, MANIFOLD MIST 15096 ANGLE, SPLASH GUARD 15043 FLAP, NEOPRINE WATER SHIELD 15204 GUARD, BLADE 18” BODY W/A 26250 SCREW, HHC 1/4-20 X 1-3/4 MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 51...
  • Page 52 FS2 CONCRETE SAW — MANUAL RAISE AND LOWER ASSY. MANUAL RAISE AND LOWER ASSY. PAGE 52 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)
  • Page 53 PIN, COTTER 1/8 X 1/2 16723 NUT, HEX FIN 8-32 13287 NUT, NYLOC 8-32 15175 SCREW, PAN HEAD 8-32 X 3/4 15127 SPACER, PIVOT 15173 WASHER, FLAT #8 MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 53...
  • Page 54 FS2 CONCRETE SAW — ENGINE ASSY. ENGINE ASSY. PAGE 54 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)
  • Page 55 ENGINE, 13HP HONDA GX390K1QXC9 15535 OIL DRAIN ASSY. 15058 BUSHING, TL 1” BORE 15059 PULLEY, TL 3V 4.12” OD 6059B KEY, 1/4”SQ. X 2” MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 55...

  • Page 56: Terms And Conditions Of Sale — Parts

    RMA. products on the face hereof. A copy of the Return Material Authorization must accompany the return shipment. PAGE 56 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)
  • Page 57 NOTE PAGE MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01) — PAGE 57...
  • Page 58 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MULTIQUIP INC. POST OFFICE BOX 6254 CARSON, CA 90749 310-537-3700 • 800-421-1244 FAX: 310-537-3927 E-MAIL: mq@multiquip.com WWW: multiquip.com Atlanta • Boise • Dallas • Houston • Newark...

Table of Contents