1. Manuals
  2. Brands
  3. Microtek Manuals
  4. Scanner
  5. ScanMaker i800 Plus
  6. Start here manual

Microtek ScanMaker i800 Plus Start Here Manual

Hide thumbs Also See for ScanMaker i800 Plus:
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

See also: Start Here Manual
Start Here
Installing your Microtek ScanMaker i800 Plus
Step 1:
Unpack your scanner package and
check for major components.
1. ScanMaker i800 Plus
2. USB cable
3. Power adapter
4. Power cord
5. Software CDs/DVDs
6. EZ-Lock™ Film Holders
Step 2:
Important: Do not remove the yellow stickers from your scanner
until you are told to do so. You must install software before
connecting your scanner.
Always close any open programs, and turn off Anti-virus utilities
before installing software.
PC:
A. Place the Adobe DVD into a drive, and install
the software. Skip this step if you have a
newer version of Photoshop Elements
already installed on your computer.
B. Place the Microtek Software CD/DVD into a
drive, and follow the on-screen instructions
to install the driver and software.
C. Insert the IT8 Calibration Data CD for the
Microtek Scanner ICC Profiler (MSP) program
into your CD/DVD-ROM drive, and follow
the on-screen instructions for installation.
D. Restart your computer at the end of all
software installation.
Copyright © 2013
Microtek International, Inc.
I49-004700 B, September 2013
Unpack Contents
1
2
Install Software
http://www.microtek.com
6
5
4
3
MAC:
A. Place the Adobe DVD into a drive, and install
the software. Skip this step if you have a
newer version of Photoshop Elements
already installed on your computer.
B. Place the Microtek Software CD/DVD into a
drive, and double-click the ScanWizard Pro
installer icon to install ScanWizard Pro first.
Next, double-click the MSP installer icon to
install the Microtek Scanner ICC Profiler
(MSP) program. Finally, insert the IT8
Calibration Data CD, and double-click the IT8
installer icon to complete MSP installation.
C. Install the remaining software components,
then restart your computer at the end of all
software installation.
NOTE: After rebooting your Macintosh, the Microtek software will
attempt to locate your scanner on the system. Since this is your
first install and you have not yet connected the scanner, simply
ignore the message that appears and proceed to the next step.
1
PRO

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ScanMaker i800 Plus and is the answer not in the manual?

Questions and answers

Related Manuals for Microtek ScanMaker i800 Plus

Summary of Contents for Microtek ScanMaker i800 Plus

  • Page 1 CD/DVD-ROM drive, and follow software installation. the on-screen instructions for installation. NOTE: After rebooting your Macintosh, the Microtek software will D. Restart your computer at the end of all attempt to locate your scanner on the system. Since this is your software installation.

  • Page 2: Unlock Scanner

    “unlocked”. Locked Unlocked NOTE: To lock the scanner (for shipping and other reasons), refer to the ScanMaker i800 Plus Supplement. Step 4: Connect Scanner To the digitizer lid Make sure the scanner lid (TMA) is properly installed, with its connector securely connected to the scanner’s 15-pin...
  • Page 3 Position the top end of the photo towards the Film Holders or Film Alignment Ruler included with back of the scanner. Then, close the lid and your ScanMaker i800 Plus package. prepare to scan. See the “Using the Remove the NOTE: Make sure the TMA”...
  • Page 4 Using the TMA A. To load film: 1. Load the film inside the EZ-Lock™ Film Holder, with the film’s shiny base facing down. • EZ-Lock 6 x 22 cm Film Holder • EZ-Lock 35mm Slide Holder • EZ-Lock 35mm Filmstrip Holder •...

  • Page 5: Scanning Photos

    2. Launch ScanWizard Pro. • If you are asked to calibrate your scanner, you can skip this section for now and come back to it later. Or, if you wish to perform calibration, see the ScanMaker i800 Plus Supplement for more details. •...
  • Page 6 Go to the Negative Scan Settings window, choose the film brand, film type, and ISO settings that match the film you use. For more details, refer to a PDF document called “ScanWizard Pro Reference Manual” in your Microtek Software CD/DVD and see the Addendum to ScanWizard Pro section.
  • Page 7 NOTE: This section only applies to the users who have IT8 calibration targets. The Microtek Scanner ICC Profiler (MSP) program included with your ScanMaker i800 Plus is used to calibrate your scanner to achieve consistent and accurate color. If the scanner you purchased contains IT8 calibration...
  • Page 8 After you finish the installation of software, if you found that the installed drivers and software cannot run your product or your computer system properly later, please go to the Microtek Download Service site at ww7.microtek.com.tw/service.php to download and install any updates you may require.

Table of Contents