Using Your Cleaner; Cleaner Maintenance - Hoover TCR 4226 Instruction Manual

uSING yOuR cleANeR

1.
extract power cord and plug it into the power supply. do not pull the cord beyond the
red marker. [5]
2.
Adjust the telescopic tube to the desired height by moving the telescopic release button
up and raise or lower the handle to the most comfortable cleaning position. [6]
3.
Select carpet care control height by pressing the pedal in the nozzle.
hard floor – brushes are lowered to protect the floor.
carpet – brushes are raised for the deepest clean.
4.
Switch the cleaner on by pressing the On/Off button on the cleaner main body.
5.
Adjust the power control regulator to the desired level.
6.
Adjust the suction regulator to the desired level.
7.
Switch off at the end of use by pressing the On/Off button. unplug and press the cord
rewind button to wind the power cord back into the cleaner. [11]
8.
To store your cleaner adjust telescopic tube to the lowest height setting and park the
nozzle in the park position on the cleaner main body. [12]
AcceSSORIeS
Please see the model specification on the packaging label for inclusion of accessories to indi-
vidual models. All accessories can be purchased separately from hoover. (See hoover Spares
and consumable section).
All accessories can be fitted to the end of the hose or the end of the telescopic tube.
3 in 1 tool – combines several functions in one. The 3 in 1 tool can be stored neatly underneath
the hose handle.
Crevice tool – for corners and hard to reach areas. [13]
Furniture nozzle – for soft furniture and fabrics [14]
dusting Brush – for bookshelves, frames, keyboards and other delicate areas. To extend the
brushes push the button on the body of the tool. [15]
parquet Caresse nozzle* – for parquet floors and other delicate floors.
grand turbo nozzle* – use the turbo nozzle for deep cleaning on carpets.
pet hair remover mini turbo nozzle* - use the mini turbo nozzle on stairs or for deepcleaning
on textile surfaces and other hard to clean areas. Particularly suitable for pet hairs removal.
allergen remover mini turbo nozzle* – use the mini turbo nozzle on stairs or for deepclean-
ing on textile surfaces and other hard to clean areas. Particularly suitable for allergen removal.
important: do not use the turbo and mini turbo nozzles on rugs with long fringes, animal
hides and carpet pile deeper than 15mm. do not keep the nozzle stationary while the brush
is rotating.
(*Certain models only)
rush_48000513__1-4-gb.indd 2
[7]
[8]
[9]
[10]

cleANeR MAINTeNANce

Emptying the dust Container
when the dust reaches the max level indicator in the container empty the dust container.
important: To maintain optimum performance do not allow the dust to sit higher than the
max level.
1.
Release the container by sliding the bin release button towards the rear of the cleaner.
[16] lift the dust container from the cleaner main body.
2.
hold the dust container over a bin with one hand and press the bin container door open
trigger. [17]
3.
close the dust container door and refit to the cleaner main body.
Cleaning the washable filters
The cleaner is fitted with a blue hepa filter pack. To maintain optimum cleaning performance
regularly remove the the filters and tap against the side of the bin to release dust. The filters
should be washed every 3 months or when the filter has excessive dust level.
important: Regularly check and maintain the filters.
important: Always ensure the filter pack is fully dry before use.
to access the filter:
1.
Release the container by sliding the bin release button towards the rear of the cleaner.
[16] lift the dust container from the cleaner main body.
2.
hold the bin with one hand and with the other hand rotate the bin handle anti clockwise
to release from the bin container. [18]
3.
Remove the foam filter from the hepa filter unit located in the bin handle.
4.
Remove the hepa filter unit from the bin handle.
5.
Gently tap and wash the grey foam filter using warm water. do not use hot water or
detergents. Remove excess water from the filter and leave to dry fully before re-using.
[21]
6.
Gently tap and wash the blue hePA filter unit. do not use hot water or detergents. Re-
move excess water from the filter and leave to dry fully before re-using. [21]
7.
Reassemble to filter pack once fully dry and refit to the cleaner.
important: do not use the product without the filter pack fitted.
to access the exhaust filter:
1.
unclip the exhaust filter from the rear of the cleaner.
2.
Gently tap and wash the grey foam filter using warm water. do not use hot water or deter-
gents. Remove excess water from the filter and leave to dry fully before re-using. [22]
2
GB
[19]
[20]
[22]
15-07-2009 12:57:03