BIRO 342 Operating Manual
  1. Manuals
  2. Brands
  3. BIRO Manuals
  4. Meat Grinder
  5. 342
  6. Operating manual

BIRO 342 Operating Manual

Heavy horsepower grinder
Hide thumbs Also See for 342:
Table of Contents

Advertisement

Quick Links

HEAVY HORSEPOWER GRINDER
OPERATING MANUAL & PARTS LIST
Models 342, 542, 548, 552, 7542, 7548, 7552, 1056, 1556
Applicable on HHP Grinders starting with Serial No. 2250
Biro Designed
Biro Built
+
+
IMPORTANT NOTICE
This Manual contains important
safety instructions which must
be strictly followed when using
PTCT
this equipment.
H400-078A
PTCT
4-10-24
H400-078A
7-04-22

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 342 and is the answer not in the manual?

Questions and answers

Related Manuals for BIRO 342

Summary of Contents for BIRO 342

  • Page 1 HEAVY HORSEPOWER GRINDER OPERATING MANUAL & PARTS LIST Models 342, 542, 548, 552, 7542, 7548, 7552, 1056, 1556 Applicable on HHP Grinders starting with Serial No. 2250 Biro Designed Biro Built IMPORTANT NOTICE This Manual contains important safety instructions which must...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Page NOTICE TO OWNERS AND OPERATORS ......... 1 SAFETY TIPS .

  • Page 3: Notice To Owners And Operators

    Manual. Warnings related to your personal safety are indicated by: Warnings related to possible damage are indicated by: BIRO also has provided warning labels on the equipment. If any warning label or Manual be- comes misplaced, damaged, or illegible, please contact your nearest Distributor or BIRO directly for a replacement.

  • Page 4: Safety Tips

    NEVER Leave Machine Unattended While Operating. NEVER Alter This Machine From its Original Form as Shipped From Factory. DO NOT Operate Machine With Parts Missing. PROMPTLY REPLACE Any Worn or Illegible Warning Labels. USE ONLY BIRO Parts and Accessories Properly Installed.

  • Page 5: Installation

    UNCRATING AND SET UP 1. Read this Manual thoroughly before installation and operation. Do not proceed with installation and operation if you have any questions or do not understand anything in this Manual. Contact your local Distributor, or BIRO first.

  • Page 6: Electrical Requirements

    11. Check placement of all warning labels and Manual. Machine is now ready for trained operators to process product. 12. Use meat deflector attached to tray to eliminate meat splatter. 13. Contact your local Distributor or BIRO directly if you have any questions or problems with the installation or operation of this machine.

  • Page 7: Wiring Diagrams

    WIRING DIAGRAM FOR HEAVY HORSEPOWER MANUAL FEED GRINDERS EQUIPPED WITH AEG OR STROMBERG STARTER (3, 5, 7 HP ONLY) STARTING WITH SERIAL NUMBER 24808 WIRING DIAGRAM FOR HEAVY HORSEPOWER MANUAL FEED GRINDERS EQUIPPED WITH AEG OR STROMBERG STARTER (10,15 HP ONLY)

  • Page 8: Operation

    OPERATION ROTATING GRINDING WORM TO AVOID SERIOUS PERSONAL INJURY ONLY Properly Trained Personnel Should Use This Equipment. NEVER Place Hands Into Machine Input or Output Openings. NEVER Open Machine During Operation. DO NOT Wear Gloves While Operating. DO NOT Tamper With, Bypass, Alter, or Modify This Equipment in Any Way From Its Original Condition.

  • Page 10: Maintenance

    NEVER Bypass, Alter, or Modify This Equipment in Any Way From Its Original Condition. PROMPTLY REPLACE Any Worn or Illegible Labels. USE ONLY GENUINE BIRO Parts and accessories Properly Installed. A. GRINDING BOWL INSTALLATION 1. Mount the grinding bowl on the two threaded studs on the front of the machine. Tighten in position with provided nuts.

  • Page 11: Bearing Housing Lubrication

    B. BEARING HOUSING LUBRICATION 1. Unplug grinder from power source and perform lockout/tagout procedures. 2. Remove bolted on tray. 3. Check and relubricate with good grade of lithium bearing grease semi-annually. 4. Reinstall tray and bolt on tightly. C. ROLLER CHAIN AND DRIVE SPROCKET LUBRICATION Chains should be protected against dirt and moisture.

  • Page 12: For 3, 5, 7 1 2 Horsepower Grinders

    IMPORTANT: Must have Model and Serial Number when ordering Parts MAIN BODY AND DRIVE SYSTEM FOR 3, 5 AND 7 HORSEPOWER GRINDERS Applicable on Choppers Starting with Serial No. 2250 Part No. Description Motor Section H301 ... . Bearing box, aluminum H328.

  • Page 13: Horsepower Grinders

    Applicable on Choppers Starting with Serial No. 2250 GRINDER HORSEPOWER AND BOWL SIZE AVAILABLE Model 342 — 3 HP — #42 size bowl — tinned Model 548 — 5 HP — #48 size bowl — tinned Model 552 — 5 HP — #52 size bowl — tinned Model 7548 —...

  • Page 14: Electrical Controls For

    (SPECIFY VOLTS COMPLETE (SPECIFY VOLTS COMPLETE NUMBER). AEG SWITCH ASSEMBLY MUST BE IN- NUMBER). AEG SWITCH ASSEMBLY MUST BE IN- STALLED QUALIFIED BIRO SERVICE STALLED QUALIFIED BIRO SERVICE AGENCY. AGENCY. CONVERSION TO AEG STARTER FROM SERIAL NO. 2250 TO SERIAL NO.
  • Page 15 (SPECIFY HP & VOLTS TO COMPLETE NO.)-LB. UNIT. AEG SWITCH ASSEMBLY LESS BUTTONS. THIS SWITCH ASSEMBLY MUST BE INSTALLED BY A QUALIFIED BIRO SERVICE AGENCY. AEG Switch Section Part Number Description H318..Switch cam, aluminum (#2250-5239 & #9039-11280) H318-1 .

  • Page 16: Parts Diagrams, Main Body And Drive System For 10 & 15 Horsepower Grinders

    IMPORTANT: Must have Model and Serial Number when ordering Parts MAIN BODY AND DRIVE SYSTEM FOR 10 AND 15 HORSEPOWER GRINDERS Applicable on Choppers Starting with Serial No. 2250 Part No. Description H101 ..... Bearing box H224 .

  • Page 17: 15 Horsepower Grinders

    IMPORTANT: Must have Model and Serial Number when ordering Parts MAIN BODY AND DRIVE SYSTEM FOR 10 AND 15 HORSEPOWER GRINDERS Applicable on Choppers Starting with Serial No. 2250 GRINDER HORSEPOWER AND BOWL SIZE AVAILABLE Model 1056 — 10 HP — #56 size bowl — tinned Model 1556 —...

  • Page 18: Electrical Controls For 10 & 15 Horsepower Grinders

    SWITCH ASSEMBLY. THIS SWITCH ASSEMBLY H278AE-18A ..Switch Assembly, BAEG/15-F23 (550V) MUST BE INSTALLED BY A QUALIFIED BIRO SER- H279AE-220..Contactor SP37.10-C0 VICE AGENCY. (208/220/230V) H279AE-380 .

  • Page 19: Operator's Signature Page

    OPERATOR'S SIGNATURE PAGE WARNING READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE SIGNING BELOW MY SIGNATURE ATTESTS THAT I HAVE COMPLETELY READ AND UNDERSTAND THIS MANUAL. I REALIZE THAT THIS MACHINE, IF OPERATED CARELESSLY, CAN CAUSE SERIOUS INJURY TO MYSELF AND OTHERS. SUPERVISOR’S NAME (PRINT) SIGNATURE...

  • Page 20: Limited Warranty

    The warranty card must be returned to The Biro Manufacturing Com- pany for proper registration. If no warranty card is returned to BIRO, the warranty period will begin from the date the machine was originally shipped from the factory.

This manual is also suitable for:

75427548542755210561556 ... Show all

Table of Contents