BIRO 346 Parts List
  1. Manuals
  2. Brands
  3. BIRO Manuals
  4. Meat Grinder
  5. 346
  6. Parts list

BIRO 346 Parts List

Hide thumbs
Table of Contents

Advertisement

Quick Links

MODEL 346 GRINDER
PARTS LIST
MODEL 346 GRINDER
Applicable Starting with Serial Number 24856
PARTS LIST
Applicable Starting with Serial Number 24856
Biro Designed
Biro Built
THE BIRO MANUFACTURING COMPANY
MARBLEHEAD, OHIO 43440-2099 U.S.A.
FAX (419) 798-9106
Phone (419) 798-4451
PTCT
PTCT
H500-203
H500-203
12-09-11
9-04-9

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 346 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for BIRO 346

Summary of Contents for BIRO 346

  • Page 1 MODEL 346 GRINDER PARTS LIST MODEL 346 GRINDER Applicable Starting with Serial Number 24856 PARTS LIST Applicable Starting with Serial Number 24856 Biro Designed Biro Built THE BIRO MANUFACTURING COMPANY MARBLEHEAD, OHIO 43440-2099 U.S.A. FAX (419) 798-9106 Phone (419) 798-4451...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Page NOTICE TO OWNERS AND OPERATORS ..........1 SAFETY TIPS .

  • Page 3: Notice To Owners And Operators

    Manual. Warnings related to your personal safety are indicated by: Warnings related to possible damage are indicated by: BIRO also has provided warning labels on the equipment. If any warning label or Manual be- comes misplaced, damaged, or illegible, please contact your nearest Distributor or BIRO directly for a replacement.

  • Page 4: Safety Tips

    NEVER Leave Machine Unattended While Operating. NEVER Alter This Machine From its Original Form as Shipped From Factory. DO NOT Operate Machine With Parts Missing. PROMPTLY REPLACE Any Worn or Illegible Warning Labels. USE ONLY BIRO Parts and Accessories Properly Installed.

  • Page 5: Installation

    UNCRATING AND SET UP 1. Read this Manual thoroughly before installation and operation. Do not proceed with installation and operation if you have any questions or do not understand anything in this Manual. Contact your local Distributor, or BIRO first.

  • Page 6: Motor Wiring And Electrical Requirements

    (H) The size of the electrical wiring required from the power source to the grinder is a MINIMUM OF No. 10 WIRE. (I) The BIRO Manufacturing Company is not responsible for permanent wiring, connection or installation. NOTE TO OWNER AND ELECTRICIAN: IF THIS MACHINE IS NOT CORD...
  • Page 7 11. Check placement of all warning labels and Manual. Machine is now ready for trained operators to process product. 12. Use meat deflector attached to tray to eliminate meat splatter. 13. Contact your local Distributor or BIRO directly if you have any questions or problems with the installation or operation of this machine.

  • Page 8: Operation

    ROTATING GRINDING WORM TO AVOID SERIOUS PERSONAL INJURY OPERATION ROTATING GRINDING WORM ONLY Properly Trained Personnel Should Use This Equipment. TO AVOID SERIOUS PERSONAL INJURY ROTATING GRINDING WORM – TO AVOID SERIOUS PERSONAL INJURY NEVER Place Hands Into Machine Input or Output Openings. ONLY Properly Trained Personnel Should Use This Equipment.

  • Page 9: Cleaning

    Electrical Components. CLEANING ALWAYS Thoroughly Clean Equipment at Least Daily. CLEANING THE BIRO MODEL 346 GRINDER 1. Disconnect grinder from power source and perform lockout/tagout procedures. 2. Remove grinding bowl end ring, breaker plate, knife and grinding worm. ROTATING GRINDING WORM...

  • Page 10: Maintenance

    NEVER Bypass, Alter, or Modify This Equipment in Any Way From Its Original Condition. PROMPTLY REPLACE Any Worn or Illegible Labels. USE ONLY GENUINE BIRO Parts and Accessories Properly Installed. A. GRINDING BOWL INSTALLATION 1. Mount the grinding bowl rear hub in the bearing box. Be sure grinding bowl is fully seated. Tighten bowl lock handle.

  • Page 11: Bearing Housing Lubrication

    B. BEARING HOUSING LUBRICATION 1. Unplug grinder from power source and perform lockout/tagout procedures. 2. Unlatch tray, lift front slightly and slide toward back of machine. Lift tray from machine and set aside. 3. Unbolt case top cover and remove. 4.

  • Page 12: Parts Diagrams

    – NOTE –...
  • Page 13 – NOTE – COUNTER-CLOCKWISE...

  • Page 15: Wiring Diagrams

    WIRING DIAGRAM FOR HEAVY HORSEPOWER MANUAL FEED GRINDERS EQUIPPED WITH AEG OR STROMBERG STARTERS WIRING DIAGRAM FOR MODEL 346 HEAVY HORSEPOWER MANUAL FEED GRINDER — 230 VOLT, 1 PHASE — EQUIPPED WITH 3HP BALDOR CAPACITOR START MOTOR SWITCHES & SWITCH COMPONENTS...

  • Page 17: Operator's Signature Page

    OPERATOR'S SIGNATURE PAGE MY SIGNATURE ATTESTS THAT I HAVE COMPLETELY READ AND UNDERSTAND THIS MANUAL. I REALIZE THAT THIS MACHINE, IF OPERATED CARELESSLY, CAN CAUSE SERIOUS INJURY TO MYSELF AND OTHERS. SUPERVISOR’S NAME (PRINT) SIGNATURE DATE INITIALS...

  • Page 18: Limited Warranty

    The warranty card must be returned to The Biro Manufacturing Com- pany for proper registration. If no warranty card is returned to BIRO, the warranty period will begin from the date the machine was originally shipped from the factory.

This manual is also suitable for:

24856

Table of Contents