Subscribe to Our Youtube Channel
Related Manuals for Sunfire CRW-2
Summary of Contents for Sunfire CRW-2
- Page 1 Cinema Ribbon In-Wall Loudspeakers CRW-2 and CRW-2C CRW-2 CRW-2C Installation Instructions and User's Manual...
-
Page 2: Important Safety Instructions
Important Safety Instructions 1. Read Instructions. 8. Refer all servicing to qualified service personnel. Servicing is required when the 2. Keep these Instructions. apparatus has been damaged in any way, 3. Heed all Warnings. such as a connector is damaged, liquid 4. -
Page 3: Table Of Contents
Break-in period ....1 Installation ....... 1 Wiring ......14 Specifications ....17 Troubleshooting ....18 Limited Warranty ..... 19 Service Assistance ..19 For more information on this and other Sunfire products, please visit our website: www.sunfire.com User's Manual... -
Page 4: Introduction
• Magnetic grille experience... the kind of heart-felt experi- ence that could only come from Sunfire. • Ribbon level control • One pair of gold-plated spring terminals The loudspeakers should only be installed by qualified and experi- •... -
Page 5: Installation Overview
The woofers - a legacy refined A system of six screw clamps secure the loudspeaker firmly in place in the Sunfire created the category of small- sheetrock, once the opening has been box, high-power subwoofers more than cut. User's Manual... -
Page 6: Features
Features CRW-C . Clamps 1. Binding Posts Once the loudspeaker is pressed into Each loudspeaker has one pair of gold- an opening in the sheetrock, screws plated spring-loaded binding posts. on the front panel are turned to pull the Always use high quality connections clamps out and down to press against and speaker wires, and make sure the sheetrock, and secure the loud-... - Page 7 CRW-C CRW- 7. Clamp Screws These screws are used to clamp the loudspeaker in place, once it has been pressed into the sheetrock opening of your wall. 8. Ribbon The CRW-C and CRW- use the same ribbon driver. 9. Lens (CRW-2C only) The CRW-C uses an acoustic lens over the ribbon to optimize the perfor- mance as a center loudspeaker.
-
Page 8: Location
Left a smooth and continuous soundfield. Sunfire Cinema Ribbon CRM-2BIP bipole loudspeakers use the same drivers and Front left and right loudspeakers ribbons as the CRW series, making them If you have a smaller TV, the loud- perfect for rear channel applications. - Page 9 5.1 Configuration If you have a Sunfire or Carver system equipped with Sonic Holography, then Place each surround loudspeaker an it is recommended that you use a tape equal distance away from your central measure to set the left and right loud-...
- Page 10 9.1 Configuration This is usually somewhere close to the corners of the room. Try Some Sunfire home theater processors locations fairly close to the front and receivers have two side-axis chan- loudspeakers, and try crouching nels that are matrixed from the left and down low.
-
Page 11: Using A Subwoofer
LFE channel: with a subwoofer to handle the frequen- cies below 80 Hz. Sunfire home theater processors and receivers have a bass management sys- tem that allows you to redirect the bass frequency range of each channel to the subwoofer. -
Page 12: Break-In Period
Cinema Ribbon CRW loud- will relax into their operating design posi- speakers. (Sunfire subwoofers have their tions and give optimum performance. own crossover controls with line-level high-pass outputs that can be used to... -
Page 13: Installation
Installation Preliminary steps: Read the details on page 8 to help determine the best position for your • If the TV display is in place, it loudspeakers. should be removed from the wall. CRW-C • Clear the area where you are going to work, so it will be safe. -
Page 14: Wiring
(see item 2 on page 6.) Do an electrical continuity test to Wiring make sure the connections are The front channels of Sunfire's Theater good from the amplifier-end of the Grand Amplifiers each have two pairs speaker wire to the ends of the of outputs. - Page 15 It is a good idea to secure the wir- ing from vibration as much as pos- sible. Do not have the weight of the cables hanging on the terminals. Fitting the loudspeaker Press the loudspeaker into the sheetrock opening, and screw in the six clamp screws.
-
Page 16: Painting The Loudspeaker
Remove the paint shield when the painting is done. Final steps The supplied Sunfire badge can now be pressed in place to match the orientation of your loudspeaker. The adhesive backing holds it in place Add the magnetic grille to cover the woofers and ribbon. -
Page 17: Specifications
Weight 15 lb (6.8 kg) CRW-C © 2008 Sunfire, LLC. Height 7.87" (200 mm) All rights reserved. Sunfire, LLC reserves Width 23.10" (587 mm) the right to improve its products at any time. Depth 4.05" (103 mm) Therefore, specifications are subject to Cutout 6.4"... -
Page 18: Troubleshooting
Troubleshooting The Cinema Ribbon CRW loudspeak- ers are designed and built to provide years of trouble-free performance. Most problems that occur can usually be solved by checking your setup, or by making sure all components are fully operational. The following information will help you deal with common problems you may experience. -
Page 19: Limited Warranty
Limited Warranty Sunfire, LLC is proud of its products Some states do not allow limitations on which have been built with care using ad- how long an implied warranty lasts and/or vanced technology and premium compo- do not allow the exclusion or limitation of nent parts. - Page 20 Cinema Ribbon In-Wall Loudspeakers CRW-2 and CRW-2C Manual 91-156-00 Rev A...
Need help?
Do you have a question about the CRW-2 and is the answer not in the manual?
Questions and answers