General Specifications - Fluke 8508A Extended Specifications

General Specifications

Power
Voltage 100 V to 120 V ±10 %
or 200 V to 240 V ±10 %
Frequency 47 Hz to 63 Hz
Consumption 80 VA
Dimensions
Height 88 mm (3.5 inches)
Width 427 mm (16.8 inches)
Depth 487 mm (19.2 inches)
Weight 11.5 kg (25.5 lbs)
Environment
Temperature:
Operating 0 °C to 50 °C
Specified Operation 5 °C to 40 °C
Calibration (TCal) 20 °C to 25 °C
Factory Cal Temperature 23 °C
Storage -20 °C to 70 °C
Warm Up 4 hours to full uncertainty
specification
Relative Humidity: (non condensing)
Operating < 90 % (5 °C to 40 °C)
Storage < 95 % (0 °C to 70 °C)
Altitude:
Operating < 2000 m
Storage < 12000 m
Vibration and Shock: Complies with MIL-PRF-28800F Class 3
EMC EN50081-1 Class B, EN55011/22,
EN61326-1:1998, EN50082-1,
EN55011 1991 Class B,
EN61000-6-1:2001, FCC Rules part 15
sub part J class B, CE marked.
Notes:
[1] Specifications apply for max resolution in each function, normal mode
[2] Assumes 4 hour warm-up period
[3] Input zero or offset null required whenever the temperature moves more than ±1 °C from the temperature at which the
previous null/zero was performed
[4] TCal = Ambient calibration temperature
[5] Integration time > 1 Power Line cycle
[6] Valid for signals >1 % Full Scale, Transfer Mode On. Signal must be DC coupled <40 Hz. Readings invalid with Transfer Mode
On and 1 Hz filter selected when using internal trigger mode
[7] Max Volt.Hertz 3 x 10 7
[8] >300 V, <10 kHz add: ±0.0004 (R-300)
>300 V, 10 kHz - 30 kHz add: ± (0.0004 + (F - 10000)*1E-7)*(R-300)
>300 V, >30 kHz add: ±0.0024 (R-300)
[9] Typical below 10 Hz for ACV, below 10 Hz, and above 10 kHz for ACI and above 2 G for Resistance
[10] Tru Ohms mode available on 2
corresponding Normal or Lo Current range.
[11] Valid for 4-wire sensor
[12] Not including sensor uncertainty
[13] Assume Range and Full Scale = 2000 V when calculating for 1000 V Range. For DCI, additional errors only apply in 5 digit
resolution
[14] Fast mode not available in PRT
General specifications
2 ppm
2
ppm
to 20 k ranges. Read Rate reduced in Tru Ohms mode. Specification for Tru Ohms same as
General Specifications (cont.)
Safety Designed and tested to EN61010-1-2001,
UL 61010-1A1,
CAN/CSA 22.2 No. 61010.1,
CE and ETL marked.
Pollution Degree 2.
Installation Category II.
Equipment Class I (single insulation /
Earthed metal case).
Protection against water ingress IP4X
(general indoor conditions).
Input circuitry and connections
(creepage and clearances) designed to
interface at Installation or Measurment
Category I.
Measurement Isolation
Guard to Safety Ground <3300 pF, >10 G
Lo to Guard:
In Remote Guard <2800 pF, >10 G
(Not in Resistance function)
In Local Guard Lo and Guard terminals are internally shorted
(in Resistance <2800 pF, >10 G )
Autorange
Range Up 100 % of nominal range
Range Down 9 % of nominal range (18 % on 1 kV range)
Remote Interface IEEE 488.2
Warranty 1 Year
2
ppm
Fluke Corporation
15
8508A Extended Specifications