Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bosch NBN-733
Summary of Contents for Bosch NBN-733
- Page 1 DINION HD 720p60 NBN-733 Installation Manual...
-
Page 3: Table Of Contents
3.1.7 Tamper detection and motion detection 3.1.8 Video encoding 3.1.9 Multicast 3.1.10 Power-over-Ethernet 3.1.11 Data interface 3.1.12 Encryption 3.1.13 Recording 3.1.14 Configuration Operation with external systems Planning Unpacking System requirements Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... - Page 4 Protected network Troubleshooting Function test Resolving problems Customer service Maintenance 10.1 Testing the network connection 10.2 Communication with Terminal Program 10.3 Repairs 10.3.1 Transfer and disposal Technical Data 11.1 Specifications AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 5: Safety
60950. The power supply must be a SELV-LPS unit or a SELV - Class 2 unit (Safety Extra Low Voltage - Limited Power Source). CAUTION! The camera must be connected to earth. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... -
Page 6: Important Safety Instructions
Equipment change or modification could void the user's guarantee or authorization agreement. Connect the earth terminal of the camera to the system earth of the installation to ensure correct safety and EMC/RFI protection. AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... -
Page 7: Connection In Applications
12 VDC or 24 VAC power supply. If auxiliary power (12 VDC or 24 VAC) and PoE is applied simultaneously, the camera selects auxiliary input and shuts off the PoE. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... -
Page 8: Fcc & Ices Compliance
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4. AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... -
Page 9: Microsd Cards
DINION HD Safety | en MicroSD cards Bosch Security systems recommends that local storage on microSD card should only be used for alarm recording and Automatic Network Replenishment (ANR) applications. To minimize the risk of loss of digital information, we recommend multiple, redundant recording systems, and a procedure to back up all digital information. -
Page 10: Bosch Notices
Bosch notices Video loss Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of lost digital information, Bosch Security Systems recommends multiple, redundant recording systems, and a procedure to back up all analog and digital information. -
Page 11: Copyrights
Digital Equipment Corporation not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission. This software is based in part on the work of the Independent JPEG Group. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... -
Page 12: Introduction
Data interface RS485/RS422/RS232 for PTZ control – Password protection – Event-driven, automatic connection – Integrated Web server for live viewing and configuration via a browser – Firmware update through web browser AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... -
Page 13: System Information
The camera complies to the ONVIF standard which means that it is easier to install and integrate into larger systems. The ONVIF standard is a global standard for the interface of network video products. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... -
Page 14: Audio
Data interface An external communications port with RS485/RS422/RS232 is available to provide data to external devices, such as pan and tilt heads, for full PTZ control via the Ethernet interface. AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... -
Page 15: Encryption
(Intranet) or from the Internet. Similarly, firmware updates and rapid loading of device configurations are also possible. Configuration settings can be stored as files on a computer and copied from one camera to another. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... -
Page 16: Operation With External Systems
The Bosch Video Management System is a unique enterprise IP video surveillance solution that provides seamless management of digital video, audio, and data across any IP network. It is designed to work with Bosch CCTV products as part of a total video surveillance management system. Bosch Video Client The camera video server and the Bosch Video Client software combine to provide a high-performance system solution. -
Page 17: Planning
Microsoft Internet Explorer web browser version 9 -or- – Computer with network access and reception software, for example Bosch Video Client, Bosch Video Management System, or Bosch Recording Station Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... -
Page 18: Installation
A spare male lens connector is provided. CAUTION! Lenses weighing more than 0.5 kg (1.1lbs) must be separately supported. Figure 5.1 Mounting a lens AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... - Page 19 Note If a short circuit is detected on the lens connector, the lens circuit is automatically disabled to avoid internal damage. Remove the lens connector and check the pin connections. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09...
-
Page 20: Mounting The Camera
(1/4" 20 UNC thread). 1/4”-20 UNC Figure 5.2 Mounting a camera CAUTION! Do not expose the image sensors to direct sunlight. Do not obstruct the free flow of air around the camera. AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... -
Page 21: Network (And Power) Connector
IP connection (green) and IP traffic (green flashing). They can be disabled in the Installer menu. Power is supplied to the camera via the Ethernet cable, compliant with the Power-over-Ethernet standard. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... -
Page 22: Power Connector
EMC/RFI protection. – Loosen the screws of the supplied 2-pole connector and insert the wires. – Tighten the screws and insert the 2-pole connector into the power socket of the camera. AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... -
Page 23: Alarm And Relay Connector
A zero potential make-contact or switch can be used as the actuator (use a bounce-free contact system). Use the alarm relay output for switching external devices such as lamps or sirens. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... -
Page 24: Audio Connectors
Audio output: Line output level (not suitable for direct speaker connection); impedance 1.5 kOhm minimum; 1 Vrms maximum output voltage. Wiring: Shielded audio connection cable is advised. Observe maximum cable lengths for audio line input and output levels. AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... -
Page 25: Local Storage
Figure 5.7 Inserting an microSD card Unscrew the card slot cover. Slide the microSD card into the slot until it locks in place. Screw the cover into place to seal the slot. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... -
Page 26: Video Service Monitor Connector
Video service monitor connector S1460 MENU INSTALL 12VDC 24VAC Figure 5.8 Video service monitor connector Connect a service monitor to the composite video connector (INSTALL) to aid installation (cable S1460). AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... -
Page 27: Data Connector
RS485, RS422, and RS232 is supported by this data connection. Note: To ensure surge and electrostatic protection, keep the cable length between the camera and external device to less than 3 meters. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... -
Page 28: Install Wizard
Zoom and focus adjustment conditions – Image orientation – Auto back focus Run the wizard to adjust the focus. This optimizes picture sharpness in both bright and low-level lighting (for example, at night). AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... -
Page 29: Adjustment Procedure
Manually adjust the focus on the lens to obtain the sharpest image possible. To rotate the image 180°, press and hold the Menu button until the image flips. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... - Page 30 If the camera is correctly focussed, briefly press the Menu button. – The back focus position is stored. – The iris is set to its original value. AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 31: Camera Configuration
User modes The camera has six user modes. These are selected via the web browser interface. The default mode is Outdoor. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... -
Page 32: True Day/Night Switching
When the auto mode is selected and the switching level is set to -15, certain borderline scene lighting conditions can cause the camera to switch back and forth between day and night modes. Set a different switching level to avoid this. AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... -
Page 33: Browser Connection
The configuration options using the menu system of the camera itself are limited to setting up the lens and network. Note: The camera can also be configured using the supplied Bosch Video Client or the Bosch Video Management System. Protected network If a RADIUS server is used for network access control (802.1x... -
Page 34: Troubleshooting
Can you connect to the camera remotely – Does the camera transmit all the data required? – Does the camera respond as desired to alarm events? – Is it possible to control peripheral devices, if necessary? AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... -
Page 35: Resolving Problems
Faulty data transmission Check the data within the LAN. transmission with ping. The maximum number of Wait until there is a free connections has been connection and call the reached. transmitter again. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... - Page 36 The interface parameters Make sure that the do not match those of the settings of all units other unit connected. involved are compatible. AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 37: Customer Service
Customer service If a fault cannot be resolved, please contact your supplier or system integrator, or go directly to Bosch Security Systems Customer Service. The version numbers of the internal firmware can be viewed on a special page. Please note this information before contacting Customer Service. -
Page 38: Maintenance
Disconnect the camera from the Ethernet network before working with the terminal program. Connect the serial interface of the camera using any available serial interface on the computer. AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... - Page 39 IP address. Use the displayed commands for any additional settings you require. Note: You must reboot to activate the new IP address, a new subnet mask or a gateway IP address. Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09...
-
Page 40: Repairs
Defective or superfluous devices and parts should be disposed of professionally or taken to your local collection point for hazardous materials. AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems... -
Page 41: Technical Data
Control feedback Actual shutter, Actual gain User modes 6 pre-defined customizable user modes LAN interface STP, Ethernet 10/100 Base-T, auto-sensing, half/full duplex, RJ-45 Video encoding H.264 (ISO/IEC 14496-10), M-JPEG protocols Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09... - Page 42 Weight without lens 690 g (1.52 lb) Operating -20 °C to +50 °C (-4 °F to +122 °F) temperature Non-IVA: -20 °C to +55 °C (-4 °F to +131 °F) AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems...
- Page 44 Bosch Security Systems www.boschsecurity.com © Bosch Security Systems, 2012...