Related Manuals for Caple WC6111
Summary of Contents for Caple WC6111
- Page 1 Instruction manual for in-column wine cabinet Model code: WC6111 Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.uk...
-
Page 2: Important Safety Instructions
If the supply cord is damaged, it must be replaced by a Caple Service agent or a similarly qualified person in order to avoid a hazard. -
Page 3: Installation Instructions
Plug the Wine cabinet into an exclusive, properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician or an authorised Caple service centre. Attention •... -
Page 4: Operating Your Wine Cabinet
OPERATING YOUR WINE CABINET AND SETTING THE TEMPERATURE CONTROL Please use the cabinet within ambient temperature of 5-32 If the ambient °C. temperature is higher or lower than this, it will cause temperature fluctuations in the cabinet. Controls LCD touch control panel. P o w e r •... - Page 5 Setting The Temperature Controls • The temperature range can be set as low as 4°Cor as high as 18°C to suit your specific storage requirements. • The standard temperature setting is 12°C. • When setting the temperature each press on the button the temperature setting will increase or decrease by 1°C.
- Page 6 Storage diagram Total: 22 bottles(Max) (for 750 ml Bordeaux bottles) Shelves • To prevent damaging the door gasket, make sure the door is fully opened when pulling shelves out of the rail compartment. • For easy access to the storage content, you must pull the shelves approximately 1/3 out of the rail compartment, however this unit was designed with a notch on each sides of the shelf tracks to prevent bottles from falling.
- Page 7 • This shelves was designed with concave grooves，Tall wine bottles can also be stored crossways on the wooden shelves. COUTION！ Do not store bottles crossways on the interior floor! Otherwise, bottles may fall out when the appliance door is opened and this may cause injury or material damage. How to change the door opening This appliance has reversible doors but is delivered with a right hinged door.
- Page 8 Incline the wine cabinet with 45 degrees, take out right lower hinge’s screws with screwdriver (Fig.1) 2. Level the wine cabinet, Hold the door and take out right upper hinge’s screws with screwdriver, then take out the door and rotate the door 180 degrees (Fig.2 & Fig.3 & Fig.4) 3.
- Page 9 Installation specifications for built-in purposes 1. After installing the wine cellar into cabinet, please adjust the limited block (a) close to cabinet (b) Please fix the 3 screws through the limited block (a) to fix to the cabinet (b), please find below picture for reference a、Limited block b、Cabinet...
-
Page 10: Care And Maintenance
CARE AND MAINTENANCE Cleaning Your Wine cabinet • Turn off the power, unplug the appliance, and remove all items including shelves and rack. • Wash the inside surfaces with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water. •... -
Page 11: Troubleshooting Guide
PROBLEMS WITH YOUR WINE CABINET? You can solve many common Wine cabinet problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer. TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE Not plugged in. -
Page 12: Humidity Maintenance System
DEFROSTING/CONDENSATION Your wine cellar is designed with an “Auto-cycle” defrost system. When the RUN cycle is OFF, the refrigerated surface of the wine cellar (interior rear wall) defrosts automatically. The defrost water is channelled into a drain pan which is located at the back of the wine cellar next to the compressor from where it evaporates.
Need help?
Do you have a question about the WC6111 and is the answer not in the manual?
Questions and answers