C900V2 Configuration Setup Instructions Table; Configuration Using Telnet; Netmask Address - Bosch Conettix C900V2 Installation Manual

Conettix C900V2 | Installation Guide | 4.0
5. Press [ENTER]. The Setup Mode information
appears.
Continue with Section 4.5.3 Configuration Using
Telnet.
4.5.3

Configuration Using Telnet

1. Type 0 (zero) and press [ENTER] to set up the
basic server configuration.
If the C900V2 was previously programmed with
an IP address, the address appears in
parentheses.
2. Type the IP address (for example,
190.200.128.219) and press [ENTER].
If you are using DHCP type 0.0.0.0 and
press [ENTER]. Refer to Section 4.1
Dynamic Host Configuration Protocol
(DHCP) on page 13.
3. If the Gateway address is required, type y,
press [ENTER] and then type the address and
press [ENTER].
If the Gateway address is not required or if you
use DHCP, type n and press [ENTER]
This prompt appears.
The Gateway IP is required only if you
are connecting to a WAN. In a LAN, the
Gateway IP is usually not needed
unless the Gateway IP of the PC is
different from the Gateway to which the
C900V2 is connected.
4. If using DHCP, press [ENTER].
If not, enter the number of bits that correspond
to the netmask your network uses and press
[ENTER]. Refer to Table 9.
Contact your network administrator if you need
more information about the netmask.
16
C900V2 Configuration Setup Instructions
Table 9:
Host Netmask
Bits
1 255.255.255.254
2 255.255.255.252
3 255.255.255.248
4 255.255.255.240
5 255.255.255.224
6 255.255.255.192
7 255.255.255.128
8 255.255.255.0
9 255.255.254.0
10 255.255.252.0
11 255.255.248.0
12 255.255.240.0
13 255.255.224.0
14 255.255.192.0
15 255.255.128.0
16 255.255.0.0
If you are using DHCP, this prompt appears.
5. If you do not want to assign or change the
name, press [ENTER].
If you want to assign a name for this device for
use on a LAN, type y and press [ENTER}.
Type the name, up to 16 characters, and press
[ENTER].
If you do not enter a DHCP device
name, a default name of Cxxxxxx is
used (where xxxxxx is the last six digits
of the MAC address).
This prompt appears.
6. Press [ENTER] to accept the password setting
at none.
In most cases, do not assign a
password. If a password is necessary,
store it in a safe place. If you lose or
forget the password, you cannot
connect to C900V2 using telnet until you
send the unit to the factory for password
removal, and the unit is returned to you.
The Setup Mode information appears.
Bosch Security Systems, Inc. | 8/08 | F01U087780-01

Netmask Address

Host Netmask
Bits
17 255.254.0.0
18 255.252.0.0
18 255.248.0.0
20 255.240.0.0
21 255.224.0.0
22 255.192.0.0
23 255.128.0.0
24 255.0.0.0
25 254.0.0.0
26 252.0.0.0
27 248.0.0.0
28 240.0.0.0
29 224.0.0.0
30 192.0.0.0
31 128.0.0.0