4-1.本製品の取り付け 次に示す手順に従って本製品を CPU ブレードに取り付けます。 注 意 高温に注意する CPU ブレードの電源を OFF にした直後は、装置内の部品が高温になっています。十分に冷めたこ とを確認してから取り付け/取り外しを行ってください。 確実に接続する CPU ブレードに取り付ける際は確実に接続してください。中途半端に取り付けると接触不良を起 こし、発煙や発火の原因となるおそれがあります。 1. 本製品を取り付ける CPU ブレードの電源が OFF(POWER ランプ消灯)になっていることを確認し ます。 CPU ブレードの電源が ON(POWER ランプ点灯)になっている場合は、各オペレー ティングシステムの電源 OFF の処理を行った後、CPU ブレードの電源を OFF に 重要 してください。 2. CPU ブレードの説明書に従ってブレード収納ユニットから本製品を取り付ける CPU ブレードを 取り出します。...
4-2.CPU ブレードの取り付け CPU ブレードの説明書に従ってブレード収納ユニットに CPU ブレードに取り付けます。 注 意 高温に注意する CPU ブレードの電源を OFF にした直後は、装置内の部品が高温になっています。十分に冷めたこ とを確認してから取り付け/取り外しを行ってください。 確実に接続する CPU ブレードを取り付ける際は確実に接続してください。中途半端に取り付けると接触不良を起 こし、発煙や発火の原因となるおそれがあります。 4-3.ドライバのインストール 本製品をご使用いただくには、各オペレーティングシステムに対応する LAN ドライバをインストー ルする必要があります。詳しくは、CPU ブレードに付属の説明書を参照してください。...
Congratulations on your purchase of the N8403-017 1000BASE-T Adapter. This User’s Guide is intended to allow you to install and use the N8403-017 1000BASE-T Adapter (hereafter called the card) correctly and safely. Read this manual thoroughly before handling the card. In addition, refer to this guide to understand how to use the card or when a problem occurs.
Page 17
Notes: No part of this manual may be reproduced in any form without the prior written permission of NEC Corporation. The contents of this manual may be revised without prior notice. The contents of this manual shall not be copied or altered without the prior written permission of NEC Corporation.
Keep this User's Guide handy for quick reference when necessary. Be sure to read this section carefully. NOTES ON USE - Always read the Notes - The following includes information necessary for proper and safe operation of the card. SAFETY INDICATIONS In the User’s Guide, "WARNING"...
Symbols Used in This Manual Attentions Indicates a general notice or warning that cannot be specifically identified. Indicates that improper use may cause an electric shock. Indicates that improper use may cause personal injury. Indicates that improper use may cause fumes or fire. Prohibited Actions Indicates a general prohibited action that cannot be specifically identified.
NEC assumes no liability for any accident resulting in personal injury, death, or property damage if this product has been used in the above conditions.
Page 21
CAUTION Avoid installation in extreme temperature conditions. Immediately after the server is powered off, its internal components such as hard disks are very hot. Leave the server until its internal components fully cool down before installing/removing any component. Connect firmly. Connect the product to the computer firmly.
Notes on Use - For Proper Operation - Note the following when you use the card. If you ignore the notes, your assets (including important data and/or other devices) may be damaged. The product is extremely sensitive to static electricity. Make sure to touch the metal frame of the Blade Enclosure to discharge static electricity from your body before handling the product.
About This Manual This guide describes how to setup and use the N8403-017 1000BASE-T Adapter. Read this guide thoroughly before using the card and store it in a safe place for future reference. When transferring the product, always include this guide.
Device failure due to shock or thermal changes, as well as operator error, may cause loss of data. To avoid loss of data, NEC recommends that you make a backup copy of your valuable data on a regular basis. Disposal Dispose of the product according to all national laws and regulations.
Transfer to Third Party ............. 24 Transportation ..............24 Data Backup ................. 24 Disposal ................24 Contents ................25 1. About N8403-017 ............26 1-1. Specifications ..............26 1-2. Features ............... 26 2. Components .............. 27 3. Names and Functions of Sections .......... 28 4.
Storage Temperature: -40 to 70ºC Humidity: 5 to 95% 1-2. Features The N8403-017 1000BASE-T Adapter is a Mezzanine card for the CPU blade of the NEC Express5800/Blade Server series. Installing this card expands the LAN port on a CPU blade.
2. Components The package contains the items listed in the table below. Make sure that all the items are provided. If you find any component missing or damaged, contact your service representative. Name Remarks 1000BASE-T Adapter (2ch) User's Guide This guide. Fixing screws Screws to secure the card to the CPU blade.
3. Names and Functions of Sections MAC address Front view Rear view Mezzanine connector Fixing screws (x3) (1) Fixing screws Use these screws to secure the card to the spacer of the CPU blade. (2) MAC address Indicates the MAC address assigned to the card. The MAC address is equivalent to the 12-digit LAN address assigned to port 1 of the card.
Take the following steps to setup the card: Explained in this User's Guide Installing card See Page 30. Install the N8403-017 Adapter in the CPU blade. Installing CPU blade See Page 31. Install the CPU blade in the Blade Enclosure. Explained in the User's...
4-1. Installation Take the following steps to install the card in the CPU blade: CAUTION Avoid installation in extreme temperature conditions. Immediately after the CPU blade is powered off, its internal components are very hot. Leave the CPU blade until its internal components fully cool down before installing/removing any component.
4-2. Installing CPU Blade Install the CPU blade in the Blade Enclosure according to the User's Guide of the CPU blade. CAUTION Avoid installation in extreme temperature conditions. Immediately after the CPU blade is powered off, its internal components are very hot.
If the same error persists, remove the card, restart the CPU blade, and check the POST screen. If POST completes normally, the card may be faulty. Contact your service representative. Notice N8403-017 1000BASE-T(2ch) User’s Guide * 856- 126417- 317- A * 456-01757-000...