General Specifications - Fluke ScopeMeter 190-502 Technical Data Manual

General Specifications

Input voltage range
Rated maximum floating voltage CAT III 1000 V/CAT IV 600 V (maximum voltage between any contact and earth-ground voltage level)
Probe input voltage VPS410
Probe input voltage VPS510
Maximum BNC input voltage
Maximum voltage
on meter input
Memory save and recall
Memory locations (internal)
15 waveform memory locations
Two recording memories
External data storage
Screencopies
Volatility
Real-time clock
Case
Design
Drip and dust proof
Shock and vibration
Display size
Resolution
Contrast and brightness
Brightness
Mechanical data
Size
Weight (including battery)
Power
Line power
Battery power
Battery type (incl.) and capacity
[+opt. battery]
Battery charge indicator
Battery operating time
(with backlight low)
Battery charging time
Battery power saving functions
Safety
Compliance
6 Fluke Corporation ScopeMeter 190 Series II
Shop for Fluke products online at:
190-062 190-102
CAT III 1000 V/CAT IV 600 V (Maximum voltage between 10:1 probe tip and reference lead)
CAT III 300 V (Maximum voltage between 10:1 probe tip and reference lead)
CAT IV 300 V (maximum voltage on BNC input directly)
CAT III 1000 V/CAT IV 600 V
(safety designed banana input connectors)
30 waveform memories plus 10 recording memories plus 9 screen copy memories (190-XX, 2 channel
models); 15 waveforms memories plus 2 recording memories plus 1 screen copy memory (190-XX, 4 channel
models)
Stores Scope-trace waveform data (2 or 4 traces each) plus screen-copy plus corresponding setup
Each may contain:
• a 100 Screen Replay sequence, or
• a ScopeRecord Roll-mode recording (2 or 4 traces), or
• a TrendPlot recording of up to 4 measurements
• On PC, using FlukeView Software, or
™
• Direct storage on external flash memory drive (maximum 2 GB) through USB host port
• On PC, using FlukeView Software, or
™
• Internally (in instrument) which can be copied on to external flash memory drive as .BMP-file,
through USB host port
Measurement data is initially stored in RAM, which is maintained by the main battery with a 30 seconds
back-up when battery is exchanged
When storing data, this is written in non-volatile flash-ROM
Provides date and time stamp information for ScopeRecord, for 100 Screen Replay sequences and
for TrendPlot recordings
Rugged, shock-proof with integrated protective holster. Handstrap and hangstrap included as standard
Kensington lock supported to lock down instrument when left unattended
IP 51 according to IEC529
Shock 30 g, vibration (sinusoidal) 3 g according to MIL-PRF-28800F Class 2
127 mm x 88 mm (153 mm/6.0 in diagonal) LCD
320 x 240 pixels
User adjustable, temperature compensated
200 cd/m typ. using power adapter, 90 cd/m
2
265 mm x 190 mm x 70 mm (10.4 in x 7.5 in x 2.8 in)
2.1 kg (4.6 lb)
Mains adapter/battery charger BC190 included, version depending of country
Re-chargeable double capacity Li-Ion battery (included). Battery swappable through
easily accessible battery door at the rear of the instrument
BP290; 2400 mAh
[BP291 (4800 mAh) optional]
Battery has built-in status indicator for use with external charger,
next to battery status indicator on instrument screen
Up to four hours using BP290 (included),
Up to eight hours using BP291 (optional)
2½ hours using BP290; 5 hours using BP291
Auto 'power down' with adjustable power down time; Auto 'Display off' with adjustable power down time;
On-screen battery power indicator
EN61010-1-2001, Pollution Degree 2;
CAN/CSA C22.2, No. 61010-1-04, with approval; UL61010B; ANSI/ISA-82.02.01
MyFlukeStore
www.
190-202 190-502
typical using battery power
2
2.2 kg (4.8 lb)
BP291; 4800 mAh
Up to seven hours using BP291 (included)
Five hours BP291
.com
190-104 190-204
—
1.877.766.5412