Hoshizaki C-101BAH Instruction Manual
  1. Manuals
  2. Brands
  3. Hoshizaki Manuals
  4. Ice Maker
  5. C-101BAH
  6. Instruction manual

Hoshizaki C-101BAH Instruction Manual

Self-contained cubelet
Hide thumbs Also See for C-101BAH:
Table of Contents

Advertisement

Quick Links

See also: Service Manual
Hoshizaki
Hoshizaki America, Inc.
Self-Contained Cubelet
Models
C-101BAH
C-101BAH-DS
C-101BAH-AD
C-101BAH-ADDS
INSTRUCTION MANUAL
"A Superior Degree
of Reliability"
www.hoshizaki.com
Issued: 7-25-2013

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C-101BAH and is the answer not in the manual?

Questions and answers

Related Manuals for Hoshizaki C-101BAH

Summary of Contents for Hoshizaki C-101BAH

  • Page 1 Hoshizaki Hoshizaki America, Inc. Self-Contained Cubelet Models C-101BAH C-101BAH-DS C-101BAH-AD C-101BAH-ADDS INSTRUCTION MANUAL “A Superior Degree of Reliability” www.hoshizaki.com Issued: 7-25-2013...
  • Page 2 Should the reader have any questions or concerns which have not been satisfactorily addressed, please call, send an e-mail message, or write to the Hoshizaki Technical Support Department for assistance. Phone: 1-800-233-1940; (770) 487-2331 Fax: 1-800-843-1056;...

  • Page 3: Table Of Contents

    B. Location ........................11 1. General ........................11 2. Built-In Installation Site ................... 12 C. Door ..........................13 1. C-101BAH, C-101BAH-AD ..................13 a) Door Reversal ....................13 2. C-101BAH-DS, C-101BAH-ADDS ................15 a) Overlay Panel Fabrication and Attachment ............15 D. Setup ........................... 23 E.

  • Page 4: Important Safety Information

    Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, damage to the appliance, or damage to property. WARNING Indicates a hazardous situation which could result in death or serious injury.
  • Page 5 WARNING, continued • The appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

  • Page 6: Specifications

    The nameplate provides electrical and refrigerant data. The nameplate is located inside the storage bin. For certification marks, see the nameplate. We reserve the right to make changes in specifications and design without prior notice. Model Number C-101BAH C-101BAH-DS C-101BAH-AD C-101BAH-ADDS...

  • Page 7: Dimensions/Connections

    C. Dimensions/Connections 1. C-101BAH...

  • Page 8: C-101Bah-Ds

    2. C-101BAH-DS...

  • Page 9: C-101Bah-Ad

    3. C-101BAH-AD...

  • Page 10: C-101Bah-Adds

    4. C-101BAH-ADDS...

  • Page 11: Installation Instructions

    II. Installation Instructions WARNING • The appliance must be installed in accordance with applicable national, state, and local codes and regulations. • CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin.

  • Page 12: Built-In Installation Site

    • Do not install the appliance in a corner where the door will interfere with other equipment or where the appliance cannot be pulled out for service. Installation Space Model Height Width Depth C-101BAH 34" (864 mm) minimum C-101BAH-DS 15" (381 mm) minimum 24" (610 mm) minimum C-101BAH-AD 32" (814 mm) minimum...

  • Page 13: Door

    C. Door 1. C-101BAH, C-101BAH-AD a) Door Reversal If you would like to reverse the door swing, follow the steps below. Otherwise, skip to section "II.D. Setup." 1) While maintaining a hold on the door, remove the hinge stop pin from hinge (B). Pull out the bottom of the door slightly and gently remove the door from hinge (A).
  • Page 14 4) Remove hinge (B) from the right side of the appliance and the 2 filler screws from the left side. Attach the 2 filler screws to the right side and attach hinge (B) to the left side. See Fig. 4. 5) Rotate the top panel 180°...

  • Page 15: C-101Bah-Ds, C-101Bah-Adds

    2. C-101BAH-DS, C-101BAH-ADDS a) Overlay Panel Fabrication and Attachment IMPORTANT The overlay panel must be crafted by a professional cabinet maker to ensure quality results. (1) Parts Ensure that all parts required for the overlay panel assembly are contained in the accessories bag.
  • Page 16 (2) Overlay Panel Specification Use the specification that applies to your appliance (C-101BAH-DS or C-101BAH-ADDS) and the directions that follow to prepare your overlay panel. (a) C-101BAH-DS C-101BAH-DS Overlay Panel Specification Overlay Panel Height 29 17/32" (750 mm) Overlay Panel Width 14 13/16"...
  • Page 17 (b) C-101BAH-ADDS C-101BAH-ADDS Overlay Panel Specification Overlay Panel Height 27 9/16" (700 mm) Overlay Panel Width 14 13/16" (376 mm) Overlay Panel Thickness 5/8" (16 mm) minimum; 3/4" (19 mm) maximum Overlay Panel and Door Weight (total) 20 lb. (9 kg) maximum...
  • Page 18 Otherwise, the overlay panel cannot be properly fastened to the door. 4) Mount the door handle hardware. Hoshizaki recommends that the door handle hardware be mounted on the edge opposite of the door hinge side (optional hinge reversal is covered in step 6.
  • Page 19 6) If you would like to reverse the door hinges, do the following: a) Contact your local distributor to purchase Hoshizaki Kit HS-0229. The kit contains "hinge (A)-left." b) Remove the 2 bolts securing the top panel, then lift it off. See Fig. 11.
  • Page 20 7) Remove the bushings from hinge (C1) and hinge (C2) (the hinges attached to the door). See Fig. 16. 8) Remove the gasket from the door. See Fig. 17. Bushing Gasket Hinge Fig. 17 Fig. 16 9) Temporarily fasten the overlay panel to the door using 2 of the M4×25 pan head screws provided.
  • Page 21 (4) Attachment of Overlay Panel to Door 1) Fasten the sheet metal bracket to the overlay panel using the two M4×8 truss head screws provided. Snug the screws, but do not tighten. See Fig. 20. 2) Temporarily fasten the overlay panel to the door using 2 of the M4×25 pan head screws provided.
  • Page 22 7) Tighten the four M4×25 pan head screws installed in step 5. See Fig. 26. 8) Replace the door gasket in its proper orientation. Reinsert the bushings into hinge (C1) and hinge (C2) (the hinges attached to the door). See Fig. 27. Bushing Tighten the screws.

  • Page 23: Setup

    D. Setup 1) Position the appliance in the selected permanent location. 2) Level the appliance from side-to-side and front-to-rear by adjusting the feet. E. Electrical Connection WARNING • Electrical connection must meet national, state, and local electrical code requirements. Failure to meet these code requirements could result in death, electric shock, serious injury, fire, or damage.

  • Page 24: Water Supply And Drain Connections

    • In areas where water damage is a concern, install in a contained area with a floor drain. • Water line installation to the appliance is not warranted by Hoshizaki. • Water-hammer issues must be resolved by a qualified plumber before installing the appliance.
  • Page 25 • For gravity drain installation, drain must have 1/4" fall per foot (2 cm per 1 m) on horizontal runs to get good flow. A vented tee connection is also required for proper flow. Extend the vent at least 12" (30 cm) above the drain outlet. •...

  • Page 26: Final Checklist

    G. Final Checklist WARNING CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. 1) Is the appliance level? 2) Is the appliance in a site where the ambient temperature is within 45°F to 100°F (7°C to 38°C) and the water temperature within 45°F to 90°F (7°C to 32°C) all year around? 3) Have the shipping carton, tape, and packing material been removed from the appliance? Has the protective plastic film been removed from the panels?

  • Page 27: Operating Instructions

    • The appliance must be maintained in accordance with the instruction manual and labels provided with the appliance. Consult with your local Hoshizaki Certified Service Representative about maintenance service. • The appliance must be cleaned and sanitized at least twice a year. More frequent cleaning and sanitizing may be required in some water conditions.
  • Page 28 NOTICE • Protect the floor when moving the appliance to prevent damage to the floor. • If using the optional drain pump (HS-5061), test its operation every time the appliance is cleaned and sanitized. See "IV.E. Optional Drain Pump HS-5061" for details.

  • Page 29: Startup

    B. Startup WARNING All parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty coverage. NOTICE • If the appliance is turned off, wait for at least 3 minutes before restarting the appliance to prevent damage to the compressor. •...

  • Page 30: Maintenance

    IV. Maintenance The appliance must be maintained in accordance with the instruction manual and labels provided with the appliance. Consult with your local Hoshizaki Certified Service Representative about maintenance service. To obtain the name and phone number of your local Hoshizaki Certified Service Representative, visit www.hoshizaki.com.

  • Page 31: Maintenance Schedule

    A. Maintenance Schedule The maintenance schedule below is a guideline. More frequent maintenance may be required depending on water quality, the appliance's environment, and local sanitation regulations. Maintenance Schedule Frequency Area Task Weekly Scoop Clean the scoop using a neutral cleaner. Rinse thoroughly after cleaning. Drain the Appliance Move the control switch to the "DRAIN"...

  • Page 32: Cleaning And Sanitizing Instructions

    1. Cleaning Solution Dilute 1.6 fl. oz. (47 ml or 3.2 tbs) of Hoshizaki "Scale Away" or Nu-Calgon "Liquid Ice Machine Cleaner" with 1 qt (1 l) of warm water. This is a minimum amount. Make more solution if necessary. IMPORTANT! For safety and maximum effectiveness, use the solution immediately after dilution.
  • Page 33 7) Make sure at least 10 minutes have elapsed since you poured the cleaning solution over the extruding head, then move the control switch to the "ICE" position. 8) Allow the appliance to make ice for 20 minutes, then move the control switch to the "DRAIN"...

  • Page 34: Storage Bin Drain

    5. Sanitizing Procedure - Final 1) Using a clean funnel and hose, pour 1 qt (1 l) of sanitizing solution over the extruding head. Allow the appliance to sit for 10 minutes before operation. 2) Move the control switch to the "ICE" position. 3) Allow the appliance to make ice for 20 minutes, then move the control switch to the "DRAIN"...

  • Page 35: Condenser

    D. Condenser Check the condenser once a year, and clean if required by following the steps below. More frequent cleaning may be required depending on location. WARNING Condenser fins are sharp. Use care when cleaning. 1) Move the control switch to the "OFF" position, then unplug the appliance from the electrical outlet.

  • Page 36: Optional Drain Pump Hs-5061

    E. Optional Drain Pump HS-5061 If the optional drain pump (HS-5061) is installed, test its operation at least twice a year as outlined below. Note that the pump has power even when the control switch is in the "OFF" position. NOTICE If the optional drain pump is not operating properly, it will adversely affect performance, component life, and warranty coverage and may result in costly water...

  • Page 37: Preparing The Appliance For Periods Of Non-Use

    V. Preparing the Appliance for Periods of Non-Use During extended periods of non-use, extended absences, or in sub-freezing temperatures, follow the instructions below. When the appliance is not used for two or three days under normal conditions, it is sufficient to move the control switch to the "OFF" position.
  • Page 38 14) Plug the appliance back in, then move the control switch to the "DRAIN" position. 15) Blow out the reservoir outlet hose using the compressed air or carbon dioxide supply. 16) Move the control switch to the "OFF" position, then unplug the appliance from the electrical outlet.

  • Page 39: Disposal

    VI. Disposal The appliance contains refrigerant and must be disposed of in accordance with applicable national, state, and local codes and regulations. Refrigerant must be recovered by properly certified service personnel.
  • Page 40 HOSHIZAKI AMERICA, INC. 618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 1A3094-010...

This manual is also suitable for:

C-101bah-dsC-101bah-adC-101bah-adds

Table of Contents