Hoshizaki C-100BAE-AD Instruction Manual
  1. Manuals
  2. Brands
  3. Hoshizaki Manuals
  4. Ice Maker
  5. C-100BAE-AD
  6. Instruction manual
Hoshizaki C-100BAE-AD Instruction Manual

Hoshizaki C-100BAE-AD Instruction Manual

Self-contained cubelet
Hide thumbs Also See for C-100BAE-AD:
Table of Contents

Advertisement

Quick Links

Hoshizaki
Hoshizaki America, Inc.
Self-Contained Cubelet
Model
C-100BAE-AD
INSTRUCTION MANUAL
"A Superior Degree
of Reliability"
www.hoshizaki.com
Issued: 3-25-2008

Advertisement

Table of Contents
loading

Related Manuals for Hoshizaki C-100BAE-AD

Summary of Contents for Hoshizaki C-100BAE-AD

  • Page 1 Hoshizaki Hoshizaki America, Inc. Self-Contained Cubelet Model C-100BAE-AD INSTRUCTION MANUAL “A Superior Degree of Reliability” www.hoshizaki.com Issued: 3-25-2008...
  • Page 2 Should the reader have any questions or concerns which have not been satisfactorily addressed, please call, write, or send an e-mail message to the HOSHIZAKI Technical Support Department for assistance. HOSHIZAKI AMERICA, INC.

  • Page 3: Important Safety Information

    Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, or damage to the unit. WARNING Indicates a hazardous situation which could result in death or serious injury. CAUTION Indicates a situation which could result in damage to the unit.

  • Page 4: Table Of Contents

    This manual should be read carefully before the icemaker is installed and operated. Only qualified service technicians should install, service, and maintain the icemaker. Read the warnings contained in this booklet carefully as they give important information regarding safety. Please retain this booklet for any further reference that may be necessary.

  • Page 5: Specifications

    I. Specifications A. Construction Top Panel Ice Discharge Opening Scoop Holder Slope Front Panel Power Switch Louver Bin Control Thermostat Magnet Catch Door...

  • Page 6: Nameplate Rating

    B. Nameplate Rating HOSHIZAKI ICE MAKER MODEL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE AMPERES DESIGN PRESSURE REFRIGERANT MOTOR-COMPRESSOR THERMALLY PROTECTED See the nameplate for electrical and refrigeration specifications. This nameplate is located on the left side panel. We reserve the right to make changes in specifications and design without prior notice.

  • Page 7: Dimensions/Connections

    C. Dimensions/Connections 1. C-100BAE-AD...

  • Page 8: Installation Instructions

    II. Installation Instructions This icemaker must be installed in accordance with applicable national, state, and local regulations. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. A.

  • Page 9: Built-In Installation Site

    1. Do not let the weight of the counter rest on the icemaker. . Do not install the icemaker in a corner where the door will interfere with other equipment or where the icemaker cannot be pulled out for service. Model C-100BAE-AD 3" (814 mm) minimum Between Two Cabinets 15"...

  • Page 10: Door Reversal

    C. Door Reversal If you would like to reverse the door hinges, follow the steps below. Otherwise, skip to section "II.D. Setup." 1) While maintaining a hold on the door, remove the hinge stop pin from hinge (B). Pull out the bottom of the door slightly and gently remove the door from hinge (A). See Fig.
  • Page 11 4) Remove hinge (B) from the right side of the unit and the  filler screws from the left side. Attach the  filler screws to the right side and attach hinge (B) to the left side. See Fig. 4. 5) Rotate the top panel 180°...

  • Page 12: Electrical Connection

    D. Setup 1) Position the icemaker in the selected permanent location. ) Level the icemaker from side-to-side and front-to-rear by adjusting the feet. E. Electrical Connection 1. This unit requires an independent power supply. See the nameplate for proper voltage and breaker/fuse size. Failure to use a proper breaker or fuse can result in a tripped breaker, blown fuse or damage to existing wiring.

  • Page 13: Water Supply And Drain Connections

    F. Water Supply and Drain Connections • Water supply and drain connections must be installed in accordance with applicable national, state, and local regulations. • A plumbing permit and services of a licensed plumber may be required in some areas. •...

  • Page 14: Final Checklist

    G. Final Checklist CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. 1) Is the icemaker level? ) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F (+7°C to +38°C) and the water temperature within +45°F to +90°F (+7°C to +3°C) all year around? 3) Have the shipping carton, tape, and packing material been removed from the...

  • Page 15: Startup

    H. Startup 1. All parts are factory-adjusted. Improper adjustments may result in failure. . If the unit is turned off, wait for at least 3 minutes before restarting it to prevent damage to the compressor. 1) Open the water supply line shut-off valve. ) Make sure the power switch is in the "OFF"...

  • Page 16: Cleaning And Maintenance

    For safety and maximum effectiveness, use the solution immediately after dilution. Dilute 1.6 fl. oz. (47 ml or 3. tbs) of recommended cleaner Hoshizaki "Scale Away" or "LIME-A-WAY" (Economics Laboratory, Inc.) with 1 qt (1 l) of warm water. This is a minimum amount.
  • Page 17 4) Remove the slope by bending its center carefully and releasing it from the  slope shafts. See Fig. 9. 5) Remove the scoop. Remove the  thumbscrews securing the scoop holder, then remove the holder. 6) Remove the  thumbscrews securing the shroud, then remove the shroud. 7) Remove the  thumbscrews securing the thermostat holder.

  • Page 18: Sanitizing Solution

    13) Replace the spout and shroud in their correct positions. 14) Plug the unit back in. Move the power switch to the "ON" position. 15) Allow the unit to make ice using the solution. When ice stops coming out, move the power switch to the "OFF"...

  • Page 19: Sanitizing Procedure - Final

    5. Sanitizing Procedure - Final 1) Remove the shroud and spout. ) Remove the drain cap to drain any remaining solution. 3) After all of the solution has drained, replace the drain cap in its correct position. 4) Remove the reservoir cover. Pour the sanitizing solution into the reservoir until the solution starts to overflow into the drain pan.

  • Page 20: Maintenance

    Consult with your local distributor about inspection and maintenance service. To obtain the name and phone number of your local distributor, call Hoshizaki Technical Support at 1-800-33-1940 in the USA. 1. Stainless Steel Exterior To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth. Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up.

  • Page 21: Preparing The Icemaker For Long Storage

    1) Move the power switch to the "OFF" position and unplug the unit from the electrical outlet. ) Remove the  screws securing the front panel, then remove the panel. See Fig. 11. 3) Remove the  screws securing the louver, then remove the louver.
  • Page 22 11) After all of the water has drained, replace the drain cap and all other removed parts in their correct positions. Ensure all components, fasteners, and thumbscrews are securely in place. Make sure that none have fallen into the storage bin. 1) From the water supply line drain valve, blow the water supply line out using compressed air or carbon dioxide.
  • Page 23 HOSHIZAKI AMERICA, INC. 618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A2UA10B...

Table of Contents