Page 1
322C 322L 325L 325L X-SERIES Operator's manual Read through the Operator‘s Manual carefully and understand the content before using the machine. 325L XT-SERIES 325C 325C X-SERIES (EPA) 101 91 71-95...
• Use anti-slip and stable boots. • Only use non-metallic, flexible cutting elements, that is trimmer head with trimmer cord. • Only intended for the trimmer head. Other symbols/decals on the machine refer to special certification requirements for certain markets.
Superauto II (322L, 325L-X/L-XT) ... 13 Assembling other guards and cutting equipment (322L, 325L-X/L-XT) ... 13 Fitting the spray guard and trimmer head (322C) ... 13 Fitting the spray guard and trimmer head (325CX) ... 14 FUEL HANDLING Fuel mixture ... 15 Fuelling...
SAFETY INSTRUCTIONS Personal protective equipment MPORTANT INFORMATION • A clearing saw, brushcutter or trimmer used incorrectly or carelessly can become a dangerous tool, that can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the content of this manual.
Page 5
• are hot and can contain sparks that can cause fires. Never start the machine indoors or close to inflammable material. 6. Cutting equipment The trimmer head is intended for trimming grass. 7. Locking nut A locking nut is used to...
Control, maintenance and service of the machine‘s safety equipment IMPORTANT INFORMATION • All service and repairs to the machine require special training. • This applies especially to the machine‘s safety equipment. If the machine does not meet any of the controls listed below you should contact your service workshop.
• Make sure the knife positioned on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a few days.
General safety instructions IMPORTANT INFORMATION • The machine is only designed for trimming grass. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “Technical data“ . •...
General working instructions IMPORTANT INFORMATION • This section takes up the basic safety precautions for working with the trimmer. • If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop.
Page 10
– English SAFETY INSTRUCTIONS Trimming • The trimmer is ideal to cut grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting.
Assembling the loop handlebar (322C, 325CX) • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the bolt, securing plate and wing nut as shown in the diagram.
• Screw on the trimmer head (H) in the direction of rotation. • Dismantling takes place in the reverse order. Fitting the spray guard and trimmer head (322C) Guard • Fit the guard as shown in the diagram. Tighten securely. Trimmer head •...
Fitting the spray guard and trimmer head (325CX) • Fit the guard as shown in the diagram. Tighten securely. • Insert the locking pin into the hole to lock the axle. • Screw the trimmer head onto the shaft. Tighten securely.
• When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For the best results use HUSQVARNA two- stroke oil, which has been specially developed for clearing saws and chain saws. Mixing ratio 1:50 (2%).
1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm. • Check that the trimmer head and spray guard are not damaged or cracked. Replace the trimmer head or spray guard if they are exposed to impact or are cracked.
Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. To ensure that your unit is at peak performance and producing the least amount of harmful...
Page 18
Final setting of the idling speed T Adjust the idling speed with the screw T, if it is necessary to readjust. First turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move. Then turn, counter-clock- wise until the cutting attachment stops.
Muffler NOTE! Some mufflers are fitted with a catalytic converter. See “Technical data” to see whether your machine is fitted with a catalytic converter. The muffler is designed to dampen the noise level and to direct the exhaust fumes away from the user. The exhaust fumes are hot and can contain sparks, which can result in fire if the...
– English MAINTENANCE NOTE: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQVARNA.
Noise and vibration measurements are made with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. Approved accessories Thread blade shaft M10 (L, L-X, L-XT) Thread blade shaft 3/8 (R) (322C) Plastic knifes Trimmer head TECHNICAL DATA...
NOTE! Noise and vibration measurements are made with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. Approved accessories Thread blade shaft 3/8 (R) Plastic knifes Trimmer head – English 325CX 1,50/24,5 1,34/34 1,06/27...
REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be perfor- med at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest &...
Page 24
Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 " – English...
Page 25
Tri Cut >20mm >20mm 6 Nm X 10 English –...
Page 26
Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6" – English...
Page 27
Trimmy Hit “Click” ~ 15 cm " 15 cm 6 " 7,0 m 12 cm 5" ~ 3,5 m “Click” English –...
Page 28
Trimmy Hit Junior 15 cm 6" “Click” – English 5,75 m ~ 2,8 m 15 cm 6" 15 cm 6"...
Page 29
Trimmy Hit Pro 15 cm 6" “Click” 15 cm 6" 7,5 m 15 cm 6" ~ 3,7 m English –...
Page 30
Trimmy Hit VI ~ 15 cm " – English 15 cm " 7,0 m 12 cm 5" ~ 3,5 m “Click”...
Page 31
Trimmy SII ~ 15 cm 35-50 NM 7,0 m 12 cm 5" ~ 3,5 m "Clic" English –...