Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Lifetime Manuals
  4. Outdoor Storage
  5. 6424
  6. Owner's manual

Lifetime 6424 Owner's Manual

30" outdoor storage extension kit
Hide thumbs Also See for 6424:

Advertisement

Quick Links

Download this manual See also: Owner's Manual & Assembly Instructions
OUTDOOR STORAGE
OUTDOOR STORAGE BUILDING
OWNER'S MANUAL
MODEL 6424
30" OUTDOOR STORAGE EXTENSION KIT

Advertisement

loading
Need help?

Need help?

Do you have a question about the 6424 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Lifetime 6424

Summary of Contents for Lifetime 6424

  • Page 1 OUTDOOR STORAGE OUTDOOR STORAGE BUILDING OWNER’S MANUAL MODEL 6424 30” OUTDOOR STORAGE EXTENSION KIT...

  • Page 2: Before Beginning Assembly

    **A MINIMUM OF TWO ADULTS ARE REQUIRED FOR ASSEMBLY** BEFORE BEGINNING ASSEMBLY Identify and inventory all parts using the checklist boxes on the Parts List. Keep the hardware bags and their contents separate. If any parts are missing, call our Customer Service Department.
  • Page 3 HARDWARE IS ACTUAL SIZE If you are Installing a New Shed 1. Check contents of boxes and compare to parts listed on the Parts List. 2. Follow instructions that came with your shed, but add extra floor panel, wall panels, Roof Cap and Skylight at appropriate points in the assembly.
  • Page 4 **Save all hardware for re-assembly!** a. Remove last three skylights. a. Remove the back 3 roof caps. a. Remove the back Roof panels and Roof support bars.
  • Page 5 a. Remove the next Roof panels and Roof support bars. a. Remove the Roof Truss.
  • Page 6 a. Remove the last two Side Wall Panels. Note: If you’re adding onto a side entry shed, remove the panels (in gray) from the side of the shed rather than removing the back of the shed. If you’re adding on to both sides, remove the panels (in gray) from both sides of the shed (as illustrated), and follow the remaining steps.
  • Page 7 Assemble Window TF (1) a. Remove plastic sheeting from Window (AE) and slide Window into slot TH (4) on the Window Wall Panel (125). Attach a Window Latch (TK) above each corner of the Window as shown. When tightening screws (TH), be sure that Window Latches will slide freely.
  • Page 8 a. Add new Floor Panel (110). Then, slide the back section into place and connect the floor panels (you will need to tip the panels forward slightly to connect the panels). Tip up one floor panel and line up tabs and then lay floor panel flat.
  • Page 9 11 Assemble Truss a. Attach Brace (AC) to two Roof Truss Channels (AB) (one on each side of Brace. Secure Brace with Screws (TF) and Nuts (TE). Follow picture above to connect Brace to a Truss Channel at each end of the Brace.
  • Page 10 c. Slide a Threaded Rod through the Truss Support Brace and the top of the Truss Connector. TD (2) d. Secure the top and bottom of the Threaded Rod with a 1/4” Cap Nut (TD). WARNING Do not overtighten the Cap Nut.
  • Page 11 a. Add Truss. a. Add Roof Panels (114) and Roof Supports (AD). b. Add a center Roof Cap (117). Roof Panel Ridge Roof Panel Wall...
  • Page 12 a. Add next Truss. a. Add Roof Panels (114) and Roof Supports (AD). b. Add a center Roof Cap (117).
  • Page 13 a. Add Roof Panels (114) and Roof Supports (AD). b. Add the last Center Roof Cap (117) and the End Roof Cap. a. Add Skylights...
  • Page 14 Enhance your Lifetime Model # 0110 Corner Shelf (2 pack) Two 10” radius shelves with hardware. 0130 30” Shelf Kit w/ hardware (3 pack) Three 30” x 10” Steel-Reinforced Shelves with shelf brackets and hardware. 0150 90” Shelf Kit w/ hardware One 90”...