Kenmore 30" DUAL FUEL RANGE Installation Instructions Manual page 6

Read the electrical connection details below.
Plug the range into the wall receptacle.
Before servicing, disconnect electrical supply at circuit
breaker, fuse or Power Cord.
PLEASE READ CAREFULLY! For personal safety, this
product must be properly grounded.
_,_ Carefully Slide Range into cabinet opening.
Carefully slide range into cabinet opening while inserting rear leveling leg into
and FULLY ENGAGING THE ANTI-TIP BRACKET (See Fig. 26). Make sure
that the flexible appliance conduit (Fig. 18) and the power cord (Fig. 20) folds
into the remaining open floor area behind the range warmer or storage drawer.
Make sure that the flexible appliance conduit does not become pinched
or kinked! Pre-shape the flexible appliance conduit and power cord if
necessary to insure that the range slides into cabinet opening properly. Be
sure to check the level of the range by placing a level horizontally on an
oven rack (See Fig. 27).
Assemble Surface Burner Heads, Cap & Grates.
Your range is shipped with the Burner Heads and Burner Caps in the correct
locations. Packing material is located between the Burner Heads and Burner
Skirts.
Example of Burner Assembly
i
i
Burner
Cap
- Electrode
Fig. 38
1. Be sure to follow the Installation Instructions before installing and using your new range.
2. Remove all packing tape from cooktop area. Remove all Burner Caps and Burner Heads.
3. Discard all packing material located under Burner Heads.
4. To replace Burner Heads & Caps, match the letters located under center of Burner Caps with the letters
located inside Burner Heads (Fig. 38).
5. Match the letters stamped on Burner Skirts with Burner Heads and Burner Caps (See Fig. 38). Replace the
Burner Heads and Caps on cooktop (See Fig. 39). Carefully align the Electrodes into slot or hole of each
Burner Head (Fig. 40). Note: The Burner Heads should sit flat on Cooktop Burner Skirts.
6. Unpack Burner Grates and position on the cooktop.
REMEMBER -- DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO
ENTER THE GAS ORIFICE HOLDER OPENING. Always keep the Burner Caps and Burner Heads in place
whenever the surface burners are in use.
(
Cooktop Layout
Fig. 39 Front of cooktop
_ Electrodes must
align into slot or hole for
each Burner Head
Fig. 40
Check Electric Ignition of Surface Burners.
Operation of electric igniters should be checked after range and supply line connectors have been carefully
checked for leaks and range has been connected to electric power.
1. To check for proper lighting, push in and turn a surface burner knob counterclockwise to the LITE
position. You will hear the igniter sparking (See Fig. 41 ).
2. The surface burner should light when gas is available to the top burner. Purge air from supply lines by
leaving knob in the LITE position until burner ignites. Each burner should light within four (4) seconds in
normal operation after air has been purged from supply lines.
3. Visually check that burner has lit. Once the burner lights, the control knob should be turned out of the LITE
position.
4. The range has separate electrodes (igniters) for each burner. Try each knob separately until all burner
valves have been checked.
Adjust the "LO" Setting of Surface Burner Valve (for Linear FlowValves only).
Test to verify if "LO" setting should be adjusted:
1. Push in and turn control to LITE until burner ignites.
2. Push in and quickly turn knob to LOWEST POSITION.
3. If burner goes out, reset control to OFF.
4. Remove the surface burner control knob.
5. Insert a thin-bladed screwdriver into the hollow valve stem and engage the slotted screw inside (See Fig. 42).
Flame size can be increased or decreased with the turn of the screw. Turn counterclockwise to increase flame
size. Turn clockwise to decrease flame size.
After installation is complete, make sure all controls are left in the OFF position.
Refer to the Use & Care Guide for cleaning instructions. If removing the range is necessary for cleaning or
maintenance, shut off the gas supply. Disconnect the gas and electrical supply. If the gas or electrical supply is
inaccessible, lift the range slightly at the front and pull out away from the wall. Pull only as far as necessary to
disconnect the gas and electrical supply. Finish removing the range for servicing and cleaning. Reinstall in reverse
order making sure to level the range and check gas connections for leaks. See page 3 of this document for proper
anti-tip anchoring instructions.
The Serial Plate is located on the right-hand surface of the oven front frame at the storage or warmer drawer; or
the lower panel area (See Fig. 43).
When ordering parts for or making inquires about your range, always be sure to include the model and serial
numbers and a lot number or letter from the Serial Plate on your range. The Serial Plate will also inform you of the
rating of the burners, the type of fuel and the pressure the range was adjusted for when it left the factory.
Fig. 41
To
Surface
Burner
Fig. 42
%
....................................... r.:..roo--._:._ . .............
Read the "Before You Call" section in your Use & Care Guide. It may save you time and expense. The list
includes common occurrences that are not the result of defective workmanship or materials for this appliance.
Refer to the warranty in your Use & Care Guide for our toll-free service number and address. Please call or write if
you have inquiries about your range product and/or need to order parts.
Open warmer drawer.
Serial plate location is here
Fig. 43