Related Manuals for Entone Kamai 400 Series
Summary of Contents for Entone Kamai 400 Series
- Page 1 Kamai Series Hybrid TV Receiver User’s Guide (North America Edition) Version 1.0 P/N: 95-88xxxx-00 V1.0...
- Page 2 COPYRIGHT DISCLAIMER TRADEMARKS CHANGES P/N: 95-88xxxx-00 CUSTOMER SUPPORT AND CONTACT INFORMATION Customer Contact Information: www.entone.com...
- Page 3 Preface ....................................5 Safety Precautions ..............................6 Index to Parts and Controls ..........................8 Kamai 400 Series Introduction ........................... 11 Connecting Kamai to the TV ..........................12 Connecting Kamai to External Digital Audio System ..................16 Using Vertical Stand ............................17 Powering-Up Kamai ............................
- Page 4 RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Copyright 2011 Entone, Inc. All rights reserved.
- Page 5 The end user manual shall include all required regulatory information/warning as show in this manual. Entone products are designed and tested to meet IEC60065, the standard for the Safety of Information Technology Equipment. This is the international standard for these types of products to reduce the risk of product damage and of personal injury.
- Page 6 This precaution may be particularly important in rural areas. CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority, or electrician, as appropriate. Copyright 2011 Entone, Inc. All rights reserved.
- Page 7 Connecting Kamai to your audio and video equipment Connecting Kamai to the network Powering Kamai Using the Remote Controls Troubleshooting For a full listing of all of the topics covered in this User’s Guide, see the Table of Contents. Copyright 2011 Entone, Inc. All rights reserved.
- Page 8 Copyright 2011 Entone, Inc. All rights reserved.
- Page 9 The battery shall not be exposed to excessive heat such as sunshine, fire or the like. Batteries are not for domestic waste. Exhausted batteries must be returned to the business or local authorities. Copyright 2011 Entone, Inc. All rights reserved.
- Page 10 Kamai Hybrid TV Receiver User’s Guide Chapter Kamai Hybrid Television Receiver (Kamai) Vertical stand RJ45 Ethernet Cable RCA A/V Cable Power Supply with power cord (100- 240V, output 12V/2.5A) IR Remote Control Battery (AA-size) Copyright 2011 Entone, Inc. All rights reserved.
- Page 11 HDMI output VIDEO Composite video output AUDIO Stereo Audio output ETHERNET RJ45 plug for connecting to ADSL modem or network access equipment DIG AUDIO Digital Audio: S/PDIF digital audio output DC power jack Copyright 2011 Entone, Inc. All rights reserved.
- Page 12 28. EXIT Exits the current menu item 29. CH UP/DOWN Changes channel up or down Changes channel to the most recently viewed 30. LAST channel 31. CC Toggles Closed Captioning on or off Copyright 2011 Entone, Inc. All rights reserved.
- Page 13 Kamai Hybrid TV Receiver User’s Guide Chapter The Kamai Hybrid TV Receiver is Entone’s most cost-effective and compact high-definition (HD) Customer Premise Equipment (CPE) solution available in the market. It is a multi-functional platform with HDTV capability and it integrates easily with popular home-networking and broadband services. It is a hybrid TV receiver that integrates traditional IPTV and Over-the-Air TV Broadcast and Cable TV, all in one box.
- Page 14 Viewer can also enjoy HD video channels on their TV through this connection. The Kamai HDMI output port is fully compliant with HDMI 1.3 specifications. Copyright 2011 Entone, Inc. All rights reserved.
- Page 15 Use the coaxial cable to connect your TV’s antenna input to the Kamai’s “TV OUT” connector. Tune your TV to channel 3 (i.e. 61.25MHz) NOTE: Coaxial cable is not included in the package and has to be purchased separately. Copyright 2011 Entone, Inc. All rights reserved.
- Page 16 1. Connect the video and audio cables from the Kamai composite “VIDEO” connector to your TV’s composite video connector. The same applies to the composite “AUDIO” connector of the Kamai and the composite audio connector of your TV. 2. Tune your TV to AV (Composite input) mode Copyright 2011 Entone, Inc. All rights reserved.
- Page 17 Analog DVI is not supported. If your TV supports digital DVI but not HDMI, you can use an HDMI to DVI convertor cable or adaptor to connect from the Kamai HDMI port to the TV DVI port. In this case, you need to connect the audio cable separately. Copyright 2011 Entone, Inc. All rights reserved.
- Page 18 Enabling or disabling AC-3 is done through the middleware application and exact steps may vary. For details of enabling and disabling AC-3, please refer to set top box usage instructions provided by your service provider. Copyright 2011 Entone, Inc. All rights reserved.
- Page 19 Kamai Hybrid TV Receiver User’s Guide Chapter A vertical stand comes packaged with Kamai so that it can be used to hold Kamai vertically. Copyright 2011 Entone, Inc. All rights reserved.
- Page 20 NOTE: Kamai can be ordered with built-in WiFi option that has internal Wi-Fi antenna. 2. Plug the socket end of the AC/DC adapter into the wall socket and the DC jack into the power connector on the Kamai. Copyright 2011 Entone, Inc. All rights reserved.
- Page 21 4. The “LINK” LED indicator will turn green. 5. Within 60 seconds, a splash screen will appear on the TV. 6. The total boot-up time may vary depending on your service provider’s network condition. Copyright 2011 Entone, Inc. All rights reserved.
- Page 22 2. If you are changing out batteries, take out all of the old batteries. 3. Put the new batteries in. Make sure you match the plus ( “+” ) ends with the plus markings on the battery case. 4. Slide the cover back into place. Copyright 2011 Entone, Inc. All rights reserved.
- Page 23 For details of how to program the Universal remote controls and the supported devices, please refer to the Kamai Quick Reference Guide or URC 4 User’s Guide. Copyright 2011 Entone, Inc. All rights reserved.
- Page 24 24-bit PCM Dolby Digital , AAC down mixed to 2 channel PCM analog stereo MPEG (ISO/IEC-11172-3) down mixed to 2 channel PCM analog stereo Closed Captioning EIA-608 Captioning format – ATSC, SCTE Copyright 2011 Entone, Inc. All rights reserved.
- Page 25 Anti-Taping Macrovision (optional) Parental Controls Provided through middleware partner integration External Adapter Model FBP045-120S250J2 INPUT 100-240 V ~ 50/60 Hz, 1.1 A max OUTPUT 12V – 2.5A NOTE: Above specification for reference only. Copyright 2011 Entone, Inc. All rights reserved.
- Page 26 Composite, Component or HDMI connection: the TV set should be set to the correct input mode for the signal. Component or HDMI connection: the resolution selected in Kamai is supported by your TV. Copyright 2011 Entone, Inc. All rights reserved.
- Page 27 Kamai to the TV possible that some TVs may not operate popping noise properly with Kamai. In case of problem, use on HDMI component video output and composite audio output to connect your primary TV. Copyright 2011 Entone, Inc. All rights reserved.