Table of Contents
Advertisement
Quick Links
48" D
UAL
**T
HESE MODELS ARE FIELD CONVERITBLE FOR
**T
HESE MODELS ARE FIELD CONVERTIBLE FOR
I
F YOU HAVE QUESTIONS
I
NSTALLATION
P
ROFESSIONAL
F
, C
, S
UEL
ONVECTION
48" N
ATURAL
*TN525-7BW
*TN525-7W
48" LP/P
ROPANE
*PN525-7BW
*PN525-7W
,
800-251-7224, 8
CALL
,
.F
WEBSITE
WWW
I
NSTRUCTIONS
R
M
ANGE
ODELS
-C
O
ELF
LEAN WITH
PEN
G
M
AS
ODELS
LP/P
G
M
AS
ODELS
N
ATURAL GAS
5
E
AM TO
PM
ASTERN
S
R
.
IVE
TAR
ANGE
COM
B
**
URNERS
.**
ROPANE GAS
.**
T
,
IME
OR VISIT OUR
.
Advertisement
Table of Contents
Related Manuals for FiveStar *TN525-7BW
Summary of Contents for FiveStar *TN525-7BW
- Page 1 NSTALLATION NSTRUCTIONS ROFESSIONAL ANGE ODELS 48” D ONVECTION LEAN WITH URNERS 48” N ATURAL ODELS *TN525-7BW *TN525-7W LP/P HESE MODELS ARE FIELD CONVERITBLE FOR ROPANE GAS 48” LP/P ROPANE ODELS *PN525-7BW *PN525-7W HESE MODELS ARE FIELD CONVERTIBLE FOR ATURAL GAS 800-251-7224, 8 F YOU HAVE QUESTIONS CALL...
-
Page 2: Installation Instructions
Be sure to leave these instructions with the Consumer. Hoods should be 24" min. deep and at least the same width as the cooktop. FiveStar hoods may be installed from 24” to 30” above the Note to Consumer • Keep these instructions for future cooking surface. - Page 3 NSTALLATION NSTRUCTIONS Please read these instructions before attempting to install this range Inspection and Unpacking Check the range carton for visible damage. If there is damage or even creases in the carton, contact the carrier, request an inspection and file the appropriate freight claim.
-
Page 4: Remove Packaging
STEP 1 REMOVE PACKAGING Before moving the range indoors: Remove outer carton and packing material from the shipping base. The range is now ready for removal from the wooden base. STEP 2 Due to the weight of these ranges, use a dolly with soft wheels to move this range. - Page 5 STEP 5 CONNECTING THE RANGE TO ELECTRIC WARNING: THIS APPLIANCE MUST BE CONNECTED AS SHOWN IN FIGURE 1 OR 2. IF A CORD IS UTILIZED IT MUST BE RATED AT 250 VOLTS, 40 AMPERES AND CERTIFIED FOR USE ON HOUSEHOLD RANGES. ELECTRICAL REQUIREMENTS FOR DUAL FUEL RANGES: 240 volts, 60 Hz, 35 amps...
-
Page 7: Connecting The Range To Gas
STEP 7 CONNECTING THE RANGE TO GAS Because hard piping restricts When using test pressures greater movement of the range, the use of an than ½ psig to pressure test the gas A.G.A. certified flexible metal supply system of the residence, appliance connector is recommended disconnect the range and individual unless local codes require a hard-... -
Page 8: Level The Range
STEP 8 LEVEL THE RANGE 1. Remove shipping tape from the leveling legs. 2. Carefully slide the range into position. Be careful not to damage the floor or entangle power cord and gas flexible tubing. 3. To adjust leveling legs, turn counter- clockwise to raise the range;... -
Page 9: Surface Burner Operation
STEP 10 ASSEMBLE SURFACE BURNER COMPONENTS • Remove shipping screw from each surface burner. • Remove each surface burner. • Place drip pan in position under each burner. Locate “dimples”. • Re-install surface burners. • Install burner pans. • Install burner grates. STEP 11 SURFACE BURNER OPERATION OPEN SURFACE BURNERS... -
Page 10: Electric Oven
STEP 12 OVEN OPERATION GAS OVEN • Turn oven thermostat knob counter clockwise to 350°. • The oven burner should light within 60 seconds. ELECTRIC OVEN • Turn oven thermostat knob counter clockwise to 350° in bake position. It will take a couple of minutes before a change in color will occur to the lower element. - Page 11 STEP 14 CHECKLIST FOR OPEN BURNER INSTALLATION MAKE SURE ALL CONTROLS ARE IN THE “OFF” POSITION. Gas supply is “on” Electric power is “on” Burner drip pans in position under burners Surface burners in position Burner pans in positions Burner grates in position Oven and broiler racks installed Surface burner ignition test Griddle/Grill burner ignition test...