Soundbar Rear-Panel Controls And Connections - JBL SB300 Quick Start Quide

SOUNDBAR REAR-PANEL CONTROLS AND
CONNECTIONS
Press this switch to initiate wireless pairing
between the soundbar and the wireless subwoofer. See Pairing the
Units for Wireless Operation , on page 6, for more information
Use this switch to adjust the soundbar's bass for either
wall or table mounting. If you're mounting the soundbar on a wall with
the included wall-mount brackets, set the EQ switch to the "Wall"
position for the most natural-sounding bass performance. If you are
placing the soundbar on a table, set the EQ switch to the "Table"
position for the most natural-sounding bass performance.
cable to connect the stereo analog outputs of your TV, DVD player or
cable/satellite tuner here.
If your TV, DVD player or cable/satellite
tuner has an optical digital output, connect it here.
Wireless Analog (AUX) Input
Pairing Switch Connections
EQ Switch
To turn the system on when the soundbar is in the
Standby mode, press the Power button on either the soundbar or
the remote. (The Power indicator will turn blue.) To put the system
in the Standby mode, press either Power button while the system is
on. (The Power indicator will turn amber.) The subwoofer will remain
on for approximately one minute after the soundbar goes into the
Standby mode. If you do not press the Power button, the soundbar
and the subwoofer will both automatically go into the Standby mode
approximately 15 minutes after the audio signal ceases.
NOTE: If you put the soundbar into the Standby mode by pressing
the Power button, you must manually turn it on by pressing the Power
button again. If the system automatically goes into the Standby
mode 15 minutes after the audio signal ceases, it will automatically
turn on whenever the soundbar detects an audio signal at the input
connection that was last used.
mute the SB300 system. (The Power indicator flashes blue.) While
the system is muted, press the Mute button again or the Volume Up
button to restore the sound.
NOTE: Momentarily pressing the soundbar's Power button while the
system is on will mute the system. Momentarily pressing the button
while the system is muted will restore the volume.
Power Surround-
Button Mode Button
Power Surround-Mode
Indicator Indicator
Use the included stereo audio
Optical Digital Input Connector
Press the Mute button to
Volume Up/ Source Selector
Down Buttons Button
Source
Indicator
NOTE: You can connect different source components to the analog
and digital connections.
Connect the included power cord here. See
Power Connections , on page 5, for more information.
IMPORTANT: Do not connect the power cord to an AC outlet until you
have made and verified all other connections.
Set this switch to the "On" position to activate the
soundbar. In normal operation, this switch will be left in the "On"
position. See Turning the Soundbar On and Off , on page 6, for more
information.
If you will not be using the soundbar for an extended period – for
instance, if you're going on vacation – set the Power switch to the
"Off" position.
Power
Switch
Power Cord Connector
This button turns the SB300 system's
3-D Surround processing on and off. The Surround Mode indicator
turns blue when 3-D Surround is active, and turns white when 3-D
Surround is not active (normal stereo sound). See Surround Mode
Buttons , on page 6, for more information. NOTE: The remote control
has individual buttons for the Stereo and 3-D Surround modes.
volume; press the "–" button to decrease the volume.
This button switches between the sources
connected to the Source 1 (analog) and Source 2 (digital) inputs.
When Source 1 is active, the Source indicator turns white; when
Source 2 is active, the Source indicator turns blue.
NOTE: The remote control has an individual button for each input
source.
On/Off
Aux
Input
Surround-Mode
Stereo
Buttons
Mute
Buttons
Press the "+" button to increase the
Power
Button
Source Selector
Digital
Input
Buttons
Surround
Vol.+
Mute
Vol.–