KitchenAid w10300233a User Instructions page 5

OPTIONS DISH LOAD TYPES DESCRIPTIONS USE WITH:
i_0 ............. "/ pans, casseroies, etc Activates the PROSCRUB® spray jets and PrOVides Duty or Normal
ProScrub with tough food s0i!, intensified water spray to the back of the lower level rack: Wash cycle
_. . ................................. ,_j May add heat and time to the cycle.
To sanitize your dishes and
glassware in accordance
with NSF/ANSI Standard
184 for Residential
Dishwashers.
Raises the water temperature in the final rinse to
approximately 155°F (68°C). This high temperature rinse
sanitizes your dishes and glassware in accordance with
NSF/ANSI Standard 184 for Residential Dishwashers.
Certified residential dishwashers are not intended for
licensed food establishments.
The Sanitize or Sani Rinse option adds heat and time to the
cycle.
Normal Wash cycle.
Heavy Duty cycle
automatically uses Sani
Rinse. Only these
sanitization cycles have
been designed to meet
the NSF/ANSI
requirements.
Loads containing tough , Increases the target water temperature during the was h Heaw Duty or Normal
Hi-Temp baked-on food. portions of the cycle. Wash cycle
Scrub i
"_._ ................ _ Adds heat, wash hme and water to the cycle.
For best drying results, dry
dishes with heat.
Turn OFF when loads contain plastic dinnerware that may be
sensitive to high temperatures.
This option with the use of rinse aid will provide the best
drying performance.
All cycles, except Rinse
Only. Automatic with all
wash cycles unless you
turn it off.
9 .............. '._ To run your dishWasher at Delays the Start of a cYcle up to 4 hoUrsl All cyciesl except Rinse
4 Hour _ a ater t'me or dur'ng off On y
Dela, -seleCt a Wash CYcle and options; press 4 HOUR DELAY.
peak hours
............................. ! Press START/RESUME, C!ose the door firm!y!
Control Lock To avoid unintended use of To turn on Lock, press and hold HEAT DRY for at least Anytime
your dishwasher, or cycle 4 seconds.
and option changes during
a cycle.
To turn off Lock, press and hold HEAT DRY for at least
4 seconds.
When Control Lock is lit, all buttons are disabled. If you press
any pad while your dishwasher is locked, the light flashes
3 times. The dishwasher door can be opened while the
controls are locked.
IMPORTANT: The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary as the sensor adjusts the
cycle for the best wash performance. If the incoming water is less than the recommended temperature or food soils are heavy, the cycle
will automatically compensate by adding time, heat and water as needed.
CONTROL PURPOSE COMMENTS
To start or iesUme a If the door is opened during a CYcle or the power is interrupted, the start/Resume indicator
wash cycle flashes. The cycle wi!l not resume until the door is closed and START/RESUME is pressed.
NOTE: If the Start!Resume button is located ontop of door, push do0r firmly cloSed Within
3 seconds of pressing START/RESUME,
To cancel wash Close the door firmly. The dishwasher starts a 2-minute drain (if needed). Let the dishwasher
cycle drain completely.
Washing
TO follow the Clean indicator glows When a Cycle is finished.
progress of your
O Drying ; , ,
If YoU select the sani Rinse option when the Sani Rinse cycle is finished the sanitized indicator
Ocl .... a snwasner CYCe glows If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the
Sanitized
cycle, This can happen if the cycle is interrupted, or the water could nat be heated to the required