Sony LMD-2451TD Operating Instructions Manual page 8

Luminance difference display
Luminance difference between the left and right signals
is displayed. This function is convenient to check the
disparity. (Software versions 1.1 or later, and BKM-
250TG with a serial number 7400001 or later)
Checkerboard
Left and right HD-SDI input signals are displayed in a
grid pattern. The two signals shown in a grid makes for
easy adjusting of the iris and color settings for the
camera. This function is only available in 2D display
mode.
L/R switch
Left and right dual-stream HD-SDI signals can be
swapped over without being visually disturbed by black
frames. This allows you to easily compare the color and
brightness between left and right signals. This function
is only available in 2D display mode.
The automatic switch of left and right signals function is
supported. The switching interval can be selected from
among SHORT, MEDIUM and LONG. (Software
versions 1.1 or later, and BKM-250TG with a serial
number 7400001 or later)
White balance offset for 3D
You can set to match the white balance for 2D and 3D
images (with glasses). Also you can set to switch the
white balance automatically when selecting 2D or 3D
display. (Software versions 1.1 or later)
Grid display function
A grid (vertical and horizontal lines) can be displayed on
the entire screen. The vertical lines are used when
checking the overall image disparity. Both the vertical
and horizontal lines are used to check the geometrical
mismatch of left and right images. (Software versions
1.1 or later, and BKM-250TG with a serial number
7400001 or later)
Disparity ruler
Two vertical lines can be displayed for measuring the
disparity value of specific subjects. (Software versions
1.1 or later, and BKM-250TG with a serial number
7400001 or later)
Virtual subject marker
Use the virtual subject marker for planning the subject
position. A square marker is displayed as a pseudo-3D
subject marker. The position and screen depth of the
marker can be adjusted for planning the real subject's
placement. The size of the square marker can also be
adjusted. (Software versions 1.1 or later, and BKM-
250TG with a serial number 7400001 or later)
Disparity simulation
The phase of either or both left and right signal for 3D
image can shift horizontally. The monitor simulates
parallax without the need for 3D rig adjustment. It saves
8
Features
time and effort in setting and adjusting the 3D rig and
equipment.
Notes
• Going out of the disparity simulation feature
initializes the parallax setting. Adjust 3D rig if
parallax needs to be changed.
• Simulated images cannot be output to any device.
Horopter check
Left/right signals for the 3D image are displayed in
selected single colors. This helps you define if the
subjects are in front of the determined screen position or
behind it. You can carefully adjust the depth of the 3D
effect using this feature. This function is only available
in 3D display mode.
Flip H
If a half mirror type rig is used, left or right signal will
be reversed. With the Flip H feature, signals that are shot
this way are horizontally reversed again for normal
viewing.
Note
A delay between left and right signals occurs as a result
of the signal processing. Because left and right signals
are internally synchronized to offset the delay, display
speed may decrease before the image reaches the screen.
Payload ID
Channel assign information of payload ID data
superimposed on input signals is displayed. You can
monitor which of two channels a left/right input signal
is assigned to.
Dual time code display
The time codes for the both left and right signals are
displayed. When the time codes are out of sync, due to
incorrect VTR settings, etc., and the time code lag is
more than one frame, the time code on the right of the
screen is displayed with the black and white inverted.
(Software versions 1.1 or later, and BKM-250TG with a
serial number 7400001 or later)
High brightness LCD panel
Because of precise image, wide viewing angle
technology and high speed response, real color image
can be reproduced.
Multi-format
The monitor supports the video, Y/C, RGB, component,
SDI (3G/HD/SD, when the optional input adaptor is
used) signals and NTSC/PAL color systems.
SDI supports not only HD-SDI and SD-SDI, but also
3G-SDI, which transmits twice as much data as HD-SDI
with a Single-link.