Sony LMD-2451TD Operating Instructions Manual page 11

a 1 (standby) switch and indicator
Press the switch to turn on the power in standby mode
(the power switch on the rear panel is turned on). The
indicator lights in green. Pressing the switch again sets
the monitor in standby mode and the indicator lights in
red.
b - (key inhibit) indicator
Lights in red when KEY INHIBIT in the KEY INHIBIT
menu is set to ON.
c CONTROL button
Press to display the buttons on the front panel. Press
again to clear the display.
d VOLUME buttons
Press the + button to increase the volume or the – button
to decrease it.
e CONTRAST buttons
Press the + button to make the contrast higher or the –
button to make it lower.
f PHASE buttons
Press the + button to make the skin tones greenish or the
– button to make them purplish.
g CHROMA buttons
Press the + button to increase the color intensity or the –
button to decrease it.
h BRIGHT (brightness) buttons
Press the + button to increase the brightness or the –
button to decrease it.
i Menu operation buttons
Displays or sets the on-screen menu.
MENU button
Press to display the on-screen menu.
Press again to clear the menu.
+/– buttons
Press to select the items and setting values.
ENTER button
Press to confirm a selected item on the menu.
When the menu is not displayed and the button is
pressed, the distinguished signal format is displayed.
RETURN button
When the menu is displayed and the button is pressed,
the value of an item is reset to the previous value.
When the menu is not displayed and the button is
pressed, the function selected in FUNCTION
BUTTON SETTING of the USER CONFIG menu is
displayed on the side of the F1 to F4 button. Also,
when the fan stops (LMD-2451TD), this button
blinks.
j Input select buttons
Press to monitor the signal input to each connector.
A-1, A-2, B-1 and B-2 buttons are used when an
optional input adaptor has been installed in the option
port.
COMPOSITE button: to monitor the signal through
the COMPOSITE IN connector
Y/C button: to monitor the signal through the Y/C IN
connector
RGB button: to monitor the RGB signal through the
connectors for the R/G/B signal input
COMPONENT button: to monitor the component
signal through the connectors for Y/P
A-1 button: to monitor the signal from connector 1
(the connectors for the R/G/B signal input in BKM-
229X) of the input adaptor installed to the option port
A
A-2 button: to monitor the signal from connector 2
(the connectors for Y/P /P
B
229X) of the input adaptor installed to the option port
A
B-1 button: to monitor the signal from connector 1
(the connectors for the R/G/B signal input in BKM-
229X) of the input adaptor installed to the option port
B
B-2 button: to monitor the signal from connector 2
(the connectors for Y/P /P
B
229X) of the input adaptor installed to the option port
B
HD15 button: to monitor the signal through the
HD15 input connector
DVI button: to monitor the signal through the DVI-D
input connector
k Function buttons
You can turn the assigned function on or off.
The factory setting is as follows;
F1 button: EXT SYNC
F2 button: SCAN
F3 button: ASPECT
F4 button: H/V DELAY
You can assign the function from among SCAN,
ASPECT, EXT SYNC, I/P MODE, MULTI DISPLAY,
CLOSED CAPTION, MONO, H/V DELAY,
MARKER, APA, BLUE ONLY, 2D/3D SELECT,
CHECKERBOARD, L/R SWITCH, HOROPTER
CHECK, DISPARITY SIM., GRID, DISPARITY
RULER, AUTO L/R SW, DIFFERENCE and
VIRTUAL SUB. MAR. in FUNCTION BUTTON
SETTING of the USER CONFIG menu (see page 31).
For details of the function assigned to the function
button, see page 31.
l Speakers
The audio signal which is selected by the input select
button is output.
Location and Function of Parts and Controls
/P signal input
B R
signal input in BKM-
R
signal input in BKM-
R
11