Changing The Settings; About The Auto Standby Function; About The Talk Over Function; Setting Preferences - Pioneer DJM-900SRT Operating Instructions Manual

Changing the settings

1 Press the [ON/OFF (UTILITY)] button for over 1 second.
The [USER SETUP] mode setting screen is displayed.
! To display the [CLUB SETUP] mode setting screen, first turn this unit's power off,
then press the [POWER] button while pressing the [ON/OFF (UTILITY)] button.
2 Press the [BEAT c, d] button.
Select the setting item.
3 Press the [TAP] button.
The screen switches to the setting item's setting value change screen.
4 Press the [BEAT c, d] button.
Change the setting value.
5 Press the [TAP] button.
Enter the setting value.
The previous screen reappears.
! To return to the previous screen without changing the settings, press the
[QUANTIZE] button.
6 Press the [ON/OFF (UTILITY)] button.
Close the [USER SETUP] mode setting screen.
! To close the [CLUB SETUP] mode setting screen, press the [POWER] button to
turn this unit's power off.

Setting preferences

*: Setting upon purchase
Mode Options settings
Fader Start
MIDI CH
MIDI Button Type
USER SETUP
Talk Over Mode
Talk Over LEVEL
Digital Master Out
Level
Digital Master Out
Sampling Rate
MASTER ATT.
Auto Standby
CLUB SETUP
Mic Output To Booth
Monitor
PC UTILITY
Peak Limiter
Factory Reset
1 Note that the output sound may be distorted even if the master level indicator does not light up to the very top.

About the setting utility software

The setting utility can be used to make the checks and settings described below.
— Checking the status of this unit's input selector switches
— Setting the audio data output from this unit to the computer
— Adjusting the buffer size (when using Windows ASIO)
— Checking the version of the driver software
Displaying the setting utility
For Windows
Click [Start] menu > [All Programs] > [Pioneer] > [DJM-900SRT] > [DJM-900SRT
Settings Utility].
24
En
Screen display Setting value
F.S. ON, OFF*
MIDI CH 1* to 16
MIDI BT TGL*, TRG
TLK MOD ADV*, NOR
–6 dB, –12 dB,
TLK LVL
–18 dB*, –24 dB
–19 dB*, –15 dB,
DOUT LV
–10 dB, –5 dB
DOUT FS 48 kHz, 96 kHz*
MST ATT –6 dB, –3 dB, 0 dB*
AUTOSTB ON*, OFF
MIC BTH ON*, OFF
PC UTLY ON, OFF*
PKLIMIT ON*, OFF
INITIAL YES, NO*

About the auto standby function

When [Auto Standby] is set to [ON], the standby mode is set automatically if 4
hours pass with all of the conditions shown below met.
— That none of this unit's buttons or controls are operated.
— That no audio signals of –10 dB or greater are input to this unit's input terminals.
— That no PRO DJ LINK connections are made.
! When the [LFO FORM (WAKE UP)] button is pressed, the standby mode is
canceled.
! This unit is shipped with the auto standby function turned on. If you do not want
to use the auto standby function, set [Auto Standby] to [OFF].

About the talk over function

The talk over function has the two modes described below.
— [ADV] (advanced talk over): The mid-range only of the sound of channels other
than the [MIC] channel is attenuated according to the [Talk Over LEVEL] setting
value and output.
dB
— [NOR] (normal talk over): The sound of channels other than the [MIC] channel is
attenuated according to the [Talk Over LEVEL] setting value and output.
dB
Descriptions
Turns the Fader Start function on and off all at once.
Sets the MIDI channel.
Selects the MIDI signal transmission mode, [TGL (TOGGLE)] or [TRG (TRIGGER)].
Selects the talk over function's mode, [ADV(ADVANCED)] or [NOR(NORMAL)].
Sets the talk over function's sound attenuation level.
Sets the maximum level of the sound output from the [DIGITAL MASTER OUT] terminals.
Sets the digital signal's sampling rate.
Sets the attenuation level of the sound output from the [MASTER1] and [MASTER2] terminals.
Turns the auto standby function on and off.
Sets whether or not to output the microphone's audio signals from [BOOTH] terminals.
Sets whether or not to launch the computer's setting utility software automatically when a USB cable is
connected.
Lessens sudden, unpleasant digital clipping of the master output.
Restores all the settings to their factory defaults.
For Mac OS X
Click [Macintosh HD] icon > [Application] > [Pioneer] > [DJM-900SRT] > [DJM-
900SRT Settings Utility].
Checking the status of this unit's input selector
switches
Display the setting utility before starting.
Frequency
Frequency
1