SETTING CONTACT
REVERSE FUNCTION
NOTE
Limit Switch and Force Adjustments must be completed before
checking the contact reversefunction.
A
Open garage door using Wall Console.
B
Lay a 2" x 4" board flat in center of doorway
(Figure
10).
C
Close door using Wall Console.
D
Check that door stops and reverses within
2 seconds after it
contacts
board:
•
If door does not reverse, decrease Close Force until
door reverses (Figure 9).
•
If door still does not reverse, move Limit Switch
toward
door.
E
Check Safe-T-Beam ® System operation:
•
If beam is blocked, door
will not close.
Figure 10 F
Checking
_J
2" x 4" board
Contact
/J_-_
laid flat
Reverse
NOTE
The door must contact the 2" x 4" board before the
Carriage activates the Close Limit Switch. If not,
readjust the Close Limit Switch.
ACCESSORIES
PROGRAMMING
THE
REMOTE CONTROL
A
To program one Button of a Remote Control (Figure 11):
•
Locate Learn Button and Learn Indicator Light near
Terminal Block on Power Head (Figure 12).
•
Press and release Learn Button. Red Learn Indicator Light
will blink 2 times per second.
•
Press Remote Control Button once within 30 seconds. Red
Learn Indicator Light will stay lit.
•
Press Remote Control Button again. Red Learn Indicator
Light will go out, indicating that memory is stored.
•
Press again to Activate Unit.
B
Program each additional
Remote using step A above.
To Erase All Remotes
from Power Head Memory
A
Press and hold Learn Button on Power Head for 10 seconds
or until Learn Indicator
Light goes out. Memory is erased:
•
Program Remotes again as needed.
To Replace
Remote
Control
Battery
A
FOR NON-FLASHLIGHTMODELS
•
Pop off the back of the transmitter.
-
Use coin, pen, screwdriver
or any similar device.
-
Replace old Battery with new coin type battery.
o
Replace back of remote.
B
FOR FLASHLIGHT MODELS
•
Slide open battery cover.
-
Replace old Battery with new AAA battery.
o
Replace battery cover.
A WARNING
A moving garage door may causeserious njury or death.
--_ Keeppeople clearof opening while door is moving.
Do not allow children to play with the RemoteControls,
If the SafetyReversedoesnot work properly:
"
Closethe door and disconnect the Opener usingthe
EmergencyRelease Cord.
,
Do not usethe door Opener,RemoteControls,or
WirelessKeypad.
•
Referto the door and door 0 pener Owner'sManuals
beforeattempting any repairs.
Remote
Control
Operation
A
B
Figure 1 1
1-Button
and 3-Button
Compact
Remotes
w/Docking
Station
Press Button on Remote Control. Garage door will move.
Press Button again. Garage door will stop:
•
The door automatically
stops at the end of the
open or close cycle.
Press Button again. Garage door will reverse.
D
There are several additional
varieties of remote controls
available from your local dealer, some equipped with
a flashlight.
LOCATED
UNDERTHE
LIGHT COVER
_b
©
.... @ (h
CLOSE
@
MORE
FORCE
©
LEARN
INDICATOR
_--
LIGHT
----
LEARN
CODE
BUTTON
Figure 12 Learn Code Button and Indicator
Light.
(Located Lower Right Corner).
NOTE
e
Each Remote Control must be programmed
separately.
•
The Remote Controls will not close the garage with
malfunctioning
Safe-T-Beam® System.
•
Program Remote Controls, while at least 24" from
Antenna Wire.
•
If the red Learn Indicator Light blinks rapidly,
programming
stopped. Restart programming.
•
Each Button on a multi-button
Remote Control is
for a different Opener. Cannot use more than one
Button for same Opener.
•
A maximum of seven Remote Controls or Wireless
Keypads can be stored into the Receiver at one
time. If a Remote Control becomes lost, or if you
want to delete a Remote Control or Wireless
Keypad, see "To EraseAll Receiver Memory."
8
For Help, call 1-800-3S-GENIE or visit www.geniecompany.com