Kenmore 625.388270 Owner's Manual page 10

[i!i !! _; _ !! _; _ SECTION 2 _i:! ! ! _; _ !! _; _ i]
HOW YOUR WATER SOFTENER WORKS
A. FACEPLATE TIMER FEATURES
S
C
T
N
,JJJJJJJJJJJJJJJJ.
,JJJJ JJJJJJJJJJ.
,JJ_JJJJJdJJJ.
,JJ JJJJJJJJJ.
,JJJ JJJJJJJJJ.
,JJ JJJJJJJJJ.
,JJJJJJJJJJJJJJJJ.
,JJJJJJJJJJJJJJJJ.
EXTRA RECHARGE
Sometimes, a manually started
regeneration (recharge) may be
desired, or needed. Two exam-
ples are:
- You have used more water than
usual (guests visiting) and you
may run out of soft water before
the next timer started regenera-
tion.
- You did not refill the softener
with salt before it was gone. After
you refill with salt:
You can start a regeneration right
away, or you can set the timer to
regenerate at the next 2:00 AM (or
other preset recharge time). Do
the following.
I1_ RECHARGE NOW [i°_] _7 -_nn_'_'L 0
Press the RECHARGE button _,_G_
and hold until *RECHARGE, Serv ..........
and Fill begin to flash in the display. Upon reaching
fill, the first cycle of regeneration, the flashing Serv
goes off and Fill is on steady. RECHARGE continues
to flash. This regeneration will last for about 2
hours. After the 2 hours, you will have soft water
again.
*Note:
If the CLEAN feature is set to ON, a cleaning back-
wash (CLEAN and Bkwsh or Rinse flashes in the dis-
play, along with the minutes of the clean cycle re-
maining) precedes the recharge.
I1_ RECHARGE TONIGHT ;°'_ -u-nq _
HjO
Press and release (do not hold) the _o,_G_ _O_,_,T
RECHARGE button. RE-
WATER FLOW
CHARGE TONIGHT flashes in the display, and the
softener begins regeneration at the next preset re-
charge time. Press and release the RECHARGE but-
ton once more if you decide to cancel the regenera-
tion, and RECHARGE TONIGHT will not flash in
the display.
I1_ SALT MONITOR SYSTEM
The face plate timer has a low salt monitor with an
indicator light to remind you to add salt to the stor-
age tank. To set this monitor system:
_1_ Lift the salt hole cover and level the salt in the
storage tank.
m
The salt level decal on the brinewell inside the
tank, has numbers from 0 to 8 (see drawing be-
low). Observe the number the leveled salt is at
or closest to.
m
Now, press the SALT LEVEL ADJUST button
until black bars display up to the salt level num-
ber. For example, the pictures below show the
salt level at 6.
E!
Finally, set the level you want the low salt indi-
cator light to come on. Press the SIGNAL LIGHT
ADJUST button until a (÷) shows opposite this
number. In the example below, the light will
come on when the stored salt drops to level 2. At
level 2, the storage tank is about 1/3 full. This is
the lowest you should allow the stored salt level
to drop to (see note on page 1-6).
_If you wish to turn the salt monitor off, press the
SIGNAL LIGHT ADJUST button until OFF
shows above.
Note:
Your salt monitor is an estimate of your salt level; ac-
curacy depends on the type of salt used and other
regeneration characteristics.
salt
level
bars, salt
level
8 ,
7 ,
6
brinewell
decal
_N
PRESS FOR
TONIGHT
HOLD FOR
IMMEDIATE
indicator light s_°w
2-1
Problems, Questions? Call 1- 800- 426- 9345 Kenmore Water Line