Advertisement
The
POWER
key serves as an indicator light during
programming, giving you feedback at each stage of the
process.
The Manual Code Search method may take a long time
because the remote searches through all of the codes in
its memory one-by-one. If your brand is listed in the Brand
Codes or the Code Lists, fi rst try the Brand Code Search or
the Direct Code Entry method.
To exit without saving a new code at any point in the
Manual Code Search, press the GO BACK key.
1.
Manually turn on the device you
want to control.
2.
If you're programming the TV or
SAT•CBL•STREAM
If you're programming the
to tell the remote which kind of device you want this
key to control, VCR or DVD.
Press and hold the
down the
DVD•VCR
the number key for the type of device you want to
control with this key: 2 for VCR, 3 for DVD.
key
3.
Press and hold the device key you want to program.
While you're holding down the device key, use your
other hand to press and hold the remote's
at the same time.
4.
Wait until the
Then release both keys.
5.
Point the remote directly at the front panel of the device
you want to control. Press
wait 2 seconds. The remote is testing a single code for
your device.
TIP: Because there are so many codes, you may have to
press the
POWER
times.
key, go to step 3.
DVD•VCR
key, you need
DVD•VCR
key. While you're holding
key, use your other hand to press
POWER
POWER
key comes on and stays on.
POWER
on the remote and
Did your device turn off?
YES: Press the STOP key to store
the code. You're done! You've
programmed this device key.
NO: Press
POWER
again. The
remote tests the next code for
your device.
Keep pressing POWER every 2
seconds until your device turns off.
When it does, press STOP.
key many times—possibly hundreds of
NOTES
Throughout the programming of each key, keep the
remote pointed at the IR sensor of the device you are
programming the remote to control.
Test the remote with the device to make sure the
device key is programmed with the correct code for
maximum functionality. If some features don't work, try
a different code. See the "Testing the Code for Maximum
Functionality" section below for more information.
During the Manual Code Search, the remote ignores
keypresses that aren't part of the search.
The search times out after two minutes (the
blinks four times and turns off, and the last programmed
code under that device key is retained).
The
POWER
key blinks four times and turns off when the
remote has gone through all the codes. The remote exits
the Manual Code Search. If your device hasn't turned off
yet, try a different search method.
Testing the Code for Maximum Functionality
1. Try a variety of the device's functions with the remote.
If some features of your devices don't work, go to the
next step to try a different code.
2. Repeat the Manual Code Search from the beginning.
When the device turns off for the fi rst time, don't
press the STOP key, which would store the same code.
Instead, with the unit now off, continue to press the
POWER key repeatedly until the unit turns back on.
3. Once the unit turns back on, you have found another
code that operates the device. Press the STOP key.
4. Test the key's functionality again by trying a variety
of functions. If the code controls the majority of the
device's functions, programming is complete. If the
code stored does not give maximum functionality, try
another code.
Tour of the Remote
In most cases, the keys
on this remote perform
key
the same functions
as the keys on your
original remotes once
you've programmed this
remote to operate your
components. Many keys
on this remote have other
functions as well.
POWER
Illuminated
serves as an indicator
light to provide feedback.
Device keys (TV,
SAT•CBL•STREAM,
DVD•VCR) put the remote
in the right mode to
control your device.
LIGHT
key (
) turns
backlighting on/off.
GUIDE/HOME and MENU
access the same features
as the keys on your
original remotes.
Arrow keys act as
navigation keys for
streaming media players
as well as in menu and
guide systems for other
devices.
POWER
key
Actual model may vary from
illustration
CHAN and VO
The CHAN ke
control for DV
functionality.
GO BACK exi
same functio
The INPUT an
toggles throu
(2) when the
between VCR
digital chann
separate the
key
number (such
IMPORTAN
Because thi
you must fi
to operate.
you must fi
TV Mode. T
you press a
remote is in
player, you
device mod
Backlight
Backlight illu
keys better in
on or off by p
stays on as lo
seconds after
timed out, an
illumination i
backlight turn
Advan
Code Ret
Once you've
devices, you
reference. If y
is easy. Just fi
of them in th
Search metho
Direct Entry m
need to retrie
the actual cod
if you ever ne
programming
codes are rec
to reprogram
quick and eas
POWER
2.
While ho
INFO-OP
holding d
key turns
3.
Release b
4.
Starting
number k
then 0. T
blink is th
number o
Hide quick links:
Advertisement
