Advertisement
4.
Press and hold the device key you want to program.
While you're holding down the device key, use your
other hand to press and hold the remote's
at the same time.
5.
Wait until the
POWER
key comes on and stays on.
Then release both keys.
6.
Look at the number you circled for
your device's brand code number.
Press that number on the remote
keypad.
7.
Point the remote directly at the
front panel of the device you want
to control. Press
POWER
on the
remote and wait 2 seconds. The
remote is testing a single code for
your device's brand.
Did your device turn off?
YES: Press the STOP key to store the code. You're
done! You've programmed this device key.
NO: Press
POWER
again. The remote tests the next
code for your brand.
Keep pressing
POWER
every 2 seconds until your
device turns off. When it does, press STOP.
NOTES
Throughout the programming of each key, be sure to
keep the remote pointed at the IR sensor of the device
you are currently programming the remote to control.
Test the remote with the device to make sure the
device key is programmed with the correct code for
maximum functionality. If some features don't work, try
a different code. See the "Testing the Code for Maximum
Functionality" section below for more information.
During the Brand Code Search, the remote ignores
keypresses that aren't part of the search.
The search times out after two minutes (the
blinks four times and turns off, and the last programmed
code under that device key is retained).
The
POWER
key blinks four times and turns off when the
remote has gone through all the codes. The remote exits
the Brand Code Search. If your device hasn't turned off
yet, try a different search method.
Testing the Code for Maximum Functionality
1. Try a variety of the device's functions with the remote.
If some device features don't work, go to the next step
to try a different code.
2. Repeat the Brand Code Search from the beginning.
When the device turns off for the fi rst time, don't
press the STOP key, which would store the same code.
Instead, with the unit now off, continue to press the
POWER key repeatedly until the unit turns back on.
3. Once the unit turns back on, you have found another
code that operates the device. Press the STOP key.
4. Test the key's functionality again by attempting to
control a variety of the device's functions. If the code
that has been stored controls the majority of the
device's functions, programming is complete. If the
code stored does not give maximum functionality, try
another code.
Direct Code Entry
Direct Code Entry lets you enter a code from the
POWER
key
accompanying code list for your brand of device. It's not as
easy as the other methods, but it's potentially the fastest
method.
TIP: Each device key is associated with a type of device—the
TV is preset to search for TVs, SAT•CBL•STREAM for
satellite receivers, cable boxes, digital TV converters, or
streaming media players, and DVD•VCR for VCRs or DVD
players.
The
POWER
programming, giving you feedback at each stage of the
process.
1.
Manually turn on the device you
want to control.
2.
Find the Code List that came with
the remote. Locate the section for
the type of device you're trying to
program, and fi nd your brand in
that section. Circle the codes for
your brand and keep them handy.
3.
Press and hold the device key you want to program
(the POWER key comes on).
While you're holding down the device key, use your
other hand enter the fi rst fi ve-digit code for your brand
in the code list (the POWER key goes off after the fi rst
digit).
4.
POWER
key
When you've fi nished entering the fi ve-digit code, keep
holding down the device key and look at the POWER
key.
Is the POWER key on?
YES: You're done! You've
NO, it blinked four times and turned off: You have
either entered a code number that is not in the code lists
or missed a step in the code entry procedure. Try step 3
again.
NOTES
Remember to enter the code for future reference in the
box provided in the Code Retrieval section of this manual.
If your brand isn't listed in the code list, use one of the
Code Search methods to program the remote control.
(Refer to the Auto and Manual Code Search methods.)
If you release the device key any time during the Direct
Code Entry procedure, the
and the process is exited. The last programmed code
under the device key is retained.
Test the remote with the device to make sure the device
key is programmed with the correct code for maximum
functionality. If some features don't work, try a different
code in the list.
key serves as an indicator light during
programmed this device key.
POWER
key blinks four times,
Auto Co
The Auto Co
codes for th
the one tha
and store th
TIPS: Each
of device—
SAT•CBL•S
digital TV c
DVD•VCR f
To exit with
Auto Code
1.
Manua
want to
2.
If you'r
SAT•C
If you'r
to tell t
key to c
Press a
down t
the num
control
3.
Press a
While y
other h
at the s
4.
Wait un
Then re
5.
Point th
front pa
want to
the rem
The rem
10 code
Did yo
YES: G
NO: Pre
of 10 co
Keep pr
turns o
Hide quick links:
Advertisement
