Download Print this page

Fujitsu C141-E280 Product/maintenance Manual

Chapter 3 installation conditions.
Hide thumbs

Advertisement

CHAPTER 3 Installation Conditions
3.1
3.2
3.3
This chapter gives the external dimensions, installation conditions, surface
temperature conditions, cable connections, and switch settings of the hard disk
drives.
C141-E280
Dimensions
Mounting
Connections with Host System
3-1

Advertisement

   Related Manuals for Fujitsu C141-E280

   Summary of Contents for Fujitsu C141-E280

  • Page 1: Chapter 3 Installation Conditions

    CHAPTER 3 Installation Conditions Dimensions Mounting Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E280...

  • Page 2

    Length of the connector pins Dimension from the outer edge of the user tap to the center of the connector pins Dimension from the outer edge of the user tap to the innermost edge of the connector pins Figure 3.1 Dimensions C141-E280...

  • Page 3

    3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be mounted in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. The mounting frame is connected to Signal Ground (SG).

  • Page 4

    Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us. Bottom surface mounting Frame of system cabinet 3.0 or less Details of A Figure 3.2 Mounting frame structure Side surface mounting Frame of system cabinet Screw 3.0 or less Screw C141-E280...

  • Page 5

    Because of breather hole mounted to the HDD, do not allow this to close during mounting. Locating of breather hole is shown as Figure 3.3. For breather hole of Figure 3.3, at least, do not allow its around φ 3 to block. Figure 3.3 Location of breather C141-E280...

  • Page 6

    Table 3.1. Figure 3.4 shows the temperature measurement point. Figure 3.4 Surface cover temperature measurement points Table 3.1 Surface temperature measurement points and standard values Measurement point DE cover Temperature 60 °C max C141-E280...

  • Page 7

    (500 kΩ or greater). Do not touch the printed circuit board, but hold it by the edges. (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. C141-E280 Mounting screw hole Figure 3.5 Service area 3.2 Mounting...

  • Page 8

    ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it. Do not stack when carrying. Do not drop. Model JX-1200-3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS C141-E280...

  • Page 9: Connections With Host System

    3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals. SATA interface and power connectors Figure 3.7 Connector locations C141-E280 3.3 Connections with Host System...

  • Page 10

    Therefore, we recommend that the customer evaluate the connector on the customer's system and select it from the connectors complying with the Serial ATA Revision 2.6 specification. 3-10 View from the connector side Signal segment View from the PCA side S1 pins in the signal segment C141-E280...

  • Page 11

    Connecting/removing the cable without releasing the SATA interface Latch may lead to connector damage and the loss of the Latch function. Accordingly, be sure to connect/remove the cable while releasing the Latch. C141-E280 3.3 Connections with Host System 3-11...

  • Page 12

    This page is intentionally blank. left...

Comments to this Manuals

Symbols: 0
Latest comments: